Xo FLOW Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 74

Xo FLOW Скачать руководство пользователя страница 51

XO FLOW – Installation instructions

51

5.16

Connecting water, compressed air, suction/drain and power supply

1.

Attach the water and air fittings to the ball valves in the floor.

2.

Connect the 6 mm white water hose and 6 mm blue air hose as shown in Figure 69. Secure the
hoses in the fittings with the locking clips supplied with the installation kit AR-135.

3.

Connect the unit suction system to the suction installation.

4.

Connect the drain hose from the unit to the wastewater installation.

Flush the water pipes and blow thoroughly through air pipe before connecting the unit.
The built-in water backflow prevention system is a legal requirement and must not be
removed.

Figure 69 – Connecting incoming air and water

5.17

Connecting 230 VAC and the suction motor

5.17.1

Connecting the power supply cable

Connect the mains supply cable to the unit as shown below in Figure 70 and position the connector
inside of the rear halfpipe cover in the bottom next to the Mains switch:

«
...
49
50
51
52
53
...
»

Содержание FLOW











































































Отзывы:

Нет отзывов