WinGD X82-B Скачать руководство пользователя страница 741

Страница: 741 / 841

PROCEDURE

Put the

template

(009,

Figure 13-13

) on the back of the

emery cloth (30 to 80 CAMI)

(008).

Use a pencil or a ball pen to make the inner shape.

Cut out accurately the shape.

Make the shape into a cone. Make sure that the graded surface (006) is the inner side.

Attach the shape to the cone of the

grinding tool

(001) with the countersunk screw.

Put the HP fuel pipe (005) in a vice.

Remove the claw from the HP fuel pipe (005).

Attach the

locknut

(004) to the threads on the end of the HP fuel pipe (005). Turn the

locknut until it is fully attached to the HP fuel pipe.

Attach the

sleeve

(003) to the HP fuel pipe (005). Make sure that the sleeve touches the

locknut (004).

Attach the grinding tool (001) to the

electric drill

(007).

Put the grinding tool (001) into the sleeve (003). Make sure that emery cloth touches the
HP fuel pipe (005).

Adjust the speed of the electric drill (007) to a maximum of 1500 rpm.

Operate the electric drill (007) for between 3 seconds to 5 seconds.

Remove the grinding tool (001) from the sleeve (003).

Use a low-pressure air supply to remove unwanted material from the HP fuel pipe (005).

Do a quality check of the sealing surface. If necessary use new emery cloth of the same
grade and do the grinding procedure again.

Replace the emery cloth with the smoother grade (

emery cloth (100 to 600 CAMI)

, then

Step 1

Step 16

again until you get a smooth finish.

Replace the emery cloth with a polishing cloth as a last step to polish the HP fuel pipe.

NOTE:

If you find large notches, you must make the HP fuel pipe (005) shorter.

Make sure that there is a minimum distance of 0.5 mm between the countersunk screw
and the sealing face (007) on the HP fuel pipe (005).

Remove the sleeve (003) and the locknut (004).

Attach the claw to the HP fuel pipe (005).

X82-B

AA00-8752-01AAA-655A-A

Maintenance Manual

HP fuel pipe (fuel pump to fuel rail) - grind the sealing face

Winterthur Gas & Diesel Ltd.

- 741 -

Issue 001 2020-10

Содержание X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X82-B

Отзывы:

Бренды по названию

Популярные бренды

WinGD X82-B, Руководство по обслуживанию

Результаты поиска

Содержание X82-B

Отзывы:

Бренды по названию

Популярные бренды