WinGD X82-B Скачать руководство пользователя страница 404

Страница: 404 / 841

PROCEDURE

Clean the seating surface of the bearing shell.

Attach the bearing shell - crank pin (008,

Figure 8-35

) to the console frame (004) with

the four screws (006).

Clean the seating surface of the connecting rod and the bearing shell (008).

Attach the spur-geared chain block (010) to the sling (011) and to the console frame
(004).

Operate the chain block (0 10) to lift the console frame (004) into position.

Attach the spur-geared chain block (002) to the console frame (004).

Remove the chain block (010).

Put oil on the surface of the bearing shell (008).

Operate the lever chain hoists (002) move the console frame (004) and bearing shell
(008) into position.

NOTE:

Make sure that the distance between each end of the bearing shell and the
connecting rod is the same.

Attach the bearing shell (008) to the connecting rod with the two screws (007).

Remove console frame (004).

Make sure that the surface of the crank pin is in a satisfactory condition.

Put oil on the crank pin.

X82-B

AA00-3303-03AAA-720A-A

Maintenance Manual

Connecting rod - install the bottom end bearing

Winterthur Gas & Diesel Ltd.

- 404 -

Issue 001 2020-10

Содержание X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X82-B

Отзывы:

Бренды по названию

Популярные бренды

WinGD X82-B, Руководство по обслуживанию

Результаты поиска

Содержание X82-B

Отзывы:

Бренды по названию

Популярные бренды