WinGD X82-B Скачать руководство пользователя страница 645

Страница: 645 / 841

2.7

Operate the chain blocks (004, 009) to hold the weight of the electric motor.

2.8

Remove the four nuts, bolts and eight washers (006) from the support.

2.9

Remove the screws from the flange (006).

2.10

Operate the chain blocks (004, 009) to remove the electric motor from the casing
as shown.

2.11

Operate the chain block (004) to release the tension until the auxiliary motor is
below the chain block (009).

2.12

Remove the chain block (004).

2.13

Attach the shackle (001) to the lug in the gallery as shown.

Fig 11-8

Electric motor (free end) - move

001

002

003

004

005

006

007

008

009

010

011

008

00867

2.14

Attach the spur-geared chain block (007,

Figure 11-9

) to the shackle (008) and

the shackle on the lifting tool (002).

2.15

Attach the shackle (010) to the lug in the gallery.

2.16

Attach the spur-geared chain block (009) to the shackle (010) and the lifting tool
(002).

2.17

Operate the chain blocks (007, 009) until the electric motor (004) is below the
chain block (007).

2.18

Remove the chain block (005).

2.19

Attach the shackle (001) to the gallery.

2.20

Attach the chain block (011) to the shackle (001).

2.21

Operate the chain blocks (009, 011) to move the electric motor (004).

2.22

Attach the engine room crane to the shackle on the lifting tool (002).

2.23

Operate the engine room crane to hold the weight of the electric motor (004).

2.24

Remove the chain blocks (009, 011) from the lifting tool (002).

X82-B

AA00-6545-00AAA-520A-A

Maintenance Manual

Auxiliary blower - remove

Winterthur Gas & Diesel Ltd.

- 645 -

Issue 001 2020-10

Содержание X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X82-B

Отзывы:

Бренды по названию

Популярные бренды

WinGD X82-B, Руководство по обслуживанию

Результаты поиска

Содержание X82-B

Отзывы:

Бренды по названию

Популярные бренды