WinGD X82-B Скачать руководство пользователя страница 176

Страница: 176 / 841

WARNING

Injury hazard. Before you operate the turning gear, make sure that no personnel are near
the flywheel, or in the engine.

Operate the turning gear to move the crankshaft in the applicable direction.

NOTE:

While the gear wheel turns, the carrier (008) moves the thrust pads. The first
thrust pad (007) will come out.

Keep a light tension on the manual ratchet (011) and the chain block (005) while the
thrust pad (007) moves up.

Remove the thrust pad (007).

Remove carefully the manual ratchet (010).

Use the chain block (005) and the manual ratchet (011) to move the thrust pad (007) to
the exhaust side.

Lower the thrust pad (007) on to a stable area.

Step 15

Step 21

for the remaining thrust pads you must remove.

X82-B

AA00-1203-00AAA-520A-A

Maintenance Manual

Thrust bearing - remove the pads

Winterthur Gas & Diesel Ltd.

- 176 -

Issue 001 2020-10

Содержание X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X82-B

Отзывы:

Бренды по названию

Популярные бренды

WinGD X82-B, Руководство по обслуживанию

Результаты поиска

Содержание X82-B

Отзывы:

Бренды по названию

Популярные бренды