WinGD X82-B Скачать руководство пользователя страница 395

Страница: 395 / 841

1.15

Operate the lever chain hoists (001, 002) to move the bearing cover (004) to the
fuel side.

1.16

Remove the lever chain hoist (001) from the bearing cover (004).

1.17

Attach the chain block (005) to the bearing cover (004).

1.18

Operate the lever chain hoist (002) and the chain block (005) to move the
bearing cover (004) from the crankcase.

1.19

Lower the bearing cover (004) on to an applicable surface.

Remove the bottom bearing shell.

2.1

Remove the two screws (007).

2.2

Attach the four eye bolts (008) to the bearing cover (004).

2.3

Attach the chain (010) to the four eye bolts (008).

2.4

Attach the chain block (005) to the chain (010).

2.5

Operate the chain block to lift the bearing shell (009) out of the bearing cover
(004).

2.6

Lower the bearing cover on to an applicable surface.

Fig 8-30

Bottom end bearing shell - remove

001 007

010

007

008

004

009

003

002

005

006

004

EXHAUST SIDE

FUEL SIDE

00767

Remove the top bearing shell.

3.1

Unlock the turning gear.

3.2

Operate the turning gear to move the crank to the fuel side until the crosshead
(001,

Figure 8-31

) is approximately 300 mm above the plug bore.

3.3

Put oil on the four bolts (004).

3.4

Attach the supports (002, 005) as follows:

3.4.1

For 6-7 Cylinder engines: Attach the two supports (002) with the four
bolts (004).

X82-B

AA00-3303-03AAA-520A-A

Maintenance Manual

Connecting rod - remove the bottom end bearing

Winterthur Gas & Diesel Ltd.

- 395 -

Issue 001 2020-10

Содержание X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X82-B

Отзывы:

Бренды по названию

Популярные бренды

WinGD X82-B, Руководство по обслуживанию

Результаты поиска

Содержание X82-B

Отзывы:

Бренды по названию

Популярные бренды