WinGD X82-B Скачать руководство пользователя страница 257

Страница: 257 / 841

PROCEDURE

Clean the items that follow:

•

O-ring grooves (005,

Figure 7-27

)

•

Sealing surfaces of the cylinder cover (004).

Put oil on the O-rings.

Clean the threads of the two elastic studs (003).

Put oil on the threads of the elastic studs (003).

Attach the engine room crane to the eye bolt (001) on the exhaust valve (002).

Operate the engine room crane to lift the exhaust valve (002).

Carefully lower the exhaust valve (002) into the cylinder cover (004).

Attach the round nuts (006) to the elastic studs (003).

Tighten the round nuts (006), refer to section

4.2 Tighten a round nut with a pre-

tensioner

Operate the engine room crane to lift the cylinder cover (004) together with the exhaust
valve (002).

Carefully lower the cylinder cover (004) on to the top water guide jacket (007).

Attach the top water guide jacket (007) to the cylinder cover (006) with the two screws
(008).

Operate the engine room crane to lift the cylinder cover (006) together with the exhaust
valve (002) and top water guide jacket (007).

X82-B

AA00-2708-00AAA-720A-A

Maintenance Manual

Cylinder cover - install

Winterthur Gas & Diesel Ltd.

- 257 -

Issue 001 2020-10

Содержание X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание X82-B

Отзывы:

Бренды по названию

Популярные бренды

WinGD X82-B, Руководство по обслуживанию

Результаты поиска

Содержание X82-B

Отзывы:

Бренды по названию

Популярные бренды