manualshive.com logo in svg

WinGD X82-B, Руководство по обслуживанию

Поделиться
Скачать
WinGD X82-B Скачать руководство пользователя страница 157

Fig 6-25

 Bearing cover No.2 to # - lift and lower

29

Attach the sling 94039-015 (005, 

Figure 6-26

) to the gallery.

30

Attach the chain block 94017-029 (003) to the sling (005).

31

Attach deviation pipes 94117C (007) and 94117B (008) to the column.

32

Attach the shackle 94019P (006) to the column.

33

Attach the chain block 94017-028 (004) to the shackle (006).

34

Operate the chain blocks (004) and (001) to move the bearing cover (002) to the fuel
side until the bearing cover hangs vertically on chain block (004).

35

Attach the chain block (003) to the bearing cover (002).

36

Remove the chain block (001) from the bearing cover (002).

37

Operate the chain blocks (004, 003) to move the bearing cover (002) out of the engine.

38

When the bearing cover (002) hangs vertically, remove the chain block (004).

39

Lower the bearing cover (002) on to an applicable surface.

40

Connect the HP oil pump 94931 to the thrust device (010).

41

Operate the HP oil pump to apply 1040 bar pressure to the thrust device.

42

Turn the screw (005) back.

43

Slowly release the pressure to zero in the HP oil pump.

44

Push in the piston (009) and remove the thrust device (010).

NOTE:

Keep the chain blocks and the sling in position.

X82-B

AA00-1132-01AAB-520A-A

Maintenance Manual

Main bearing cover - No. 2 to # - remove

Winterthur Gas & Diesel Ltd.

- 157 -

Issue 001 2020-10

Содержание X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды