Wfly ET Series Скачать руководство пользователя

Страница: 111 / 131

Rudder to Aileron

Interface path: WFLY → [Model Menu] → [Rudder to Aileron]

This function is required when mixing ailerons and rudders. This function is used when the rudder is used

for roll, such as side ﬂying. Can also be applied to tilting or turning in a real machine, large model or full size
model.

●

This function can be used to control "on" / "oﬀ" with the switch during ﬂight. (If you want to keep it on,

set it to [--], you can also set it to [--], and the position is "On" to achieve the function normally open.)

● Setp function: It can connect this mix to other mixes.
● The mixing rate of this function can be adjusted.
● Three types of curves can be set.

* Flight conditions: Set the "Flight Conditio" control switch in [Model Menu] → [Condition]. Switching by

switch to perform function setting separately.

Rudder to aileron

1/2

Switch

Link

Status

INH

- -

OFF

Function status button

(INH, ON, default [INH])

Function control switch (default [--])

Connect this mix to other mixes (default [oﬀ])

Rudder

Rudder2

Rudder

Rudder2

Rudder

V-tail

Rudder to aileron

2/2

Oﬀset

Type

EXP1

Rate B

Rate A

100%

EXP B

EXP A

100%

+15 0

+1 0 0

+50

- 50

- 1 0 0

- 1 5 0

+150%

RAT E

+150%

PO S

111

Model Menu\Glider

Содержание ET Series




































































































































Результаты поиска

Содержание ET Series

Отзывы:

Похожие инструкции для ET Series

Бренды по названию

Популярные бренды

Wfly ET Series, Инструкция по эксплуатации

Результаты поиска

Содержание ET Series

Отзывы:

Похожие инструкции для ET Series

Бренды по названию

Популярные бренды