Wfly ET Series Скачать руководство пользователя страница 93

Страница: 93 / 131

Camber Mix

Camber mix

Status

INH

Switch

AIL

+0%

AIL2

+0%

FLP

+0%

FLP2

+0 %

Rate1

Rate2

- -

Interface path: WFLY → [Model Menu] → [Camber mix]

This function is used to adjust the operating ratio on the positive and negative directions (ailerons,

ﬂaps) of the airfoil ﬂaps. The ratio of the ailerons, ﬂaps, and elevators can be individually adjusted to
correct for changes in attitude caused by airfoil operations. The interface of diﬀerent wing types will also be
the same.

Function switch (INH, ON, default [INH])

Control switch assignment, default [--]

Diﬀerent aircraft types will have diﬀerent wings

Adjust in the positive and negative directions,
range ±100%, default 0%

The up/down ratio of the ailerons, ﬂaps, and elevators can be adjusted separately using curves. When

the mechanical connection action of the fuselage is opposite to the mixing direction, the mixing polarity can
be changed to adjust (+ or -).

This function can be switched "on" or "oﬀ" with the switch during ﬂight. (If you want to keep it on, set it to

[--], you can also set it to [--], and the position is "On" to achieve the function normally open.)

* Flight conditions: Set the "Flight Condition" control switch in [Model Function] → [Condition]. Switching

is performed by switches, and function settings are made separately.

Elevator

Elevator2(Ailevator)

Aileron

Aileron2

V-Tail

Flaps

Flaps2

093

Model Menu\Airplane

Содержание ET Series




































































































































Результаты поиска

Содержание ET Series

Отзывы:

Бренды по названию

Популярные бренды

Wfly ET Series, Инструкция по эксплуатации

Результаты поиска

Содержание ET Series

Отзывы:

Бренды по названию

Популярные бренды