manualshive.com logo in svg

Wfly ET Series, Инструкция по эксплуатации

Поделиться
Скачать
Wfly ET Series Скачать руководство пользователя страница 41

Linkage Setting

Link

Interface path: WFLY→[Linkage Setting]→[Link 

Step]

The link function is used for matching the 

transmitter and receiver.

Telemetry: Data backhaul function. Mainly used 

for functional judgment and data analysis, shutdown 
telemetry will affect the use of security functions. 
The default Telemetry is on, it is recommended to 
turn on!

Mode: Working mode selection(default working 

mode A). Please refer to the table on the right. The 
channel marked in the table is defined as the default 
configuration. You can customize the channel by 
[Receiver Output].

Link: Immediately link the transmitter and 

receiver. Clicking link will bring up the confirmation 
box.

Receiver slot

Channel User defined

Model A

Model B

1

1

7

2

2

8

3

3

3

4

4

9

5

5

10

6

6

11

7

7

12

8

W

.

BUS

/

PPM

W

.

BUS

/

PPM

9

W

.

BUS2

W

.

BUS2

When linking, please be careful not to 

connect the power equipment, and 
remove the propeller, pay attention to 
safety!

To ensure safety, please do not link in 

the status where the motor and engine 
are running.

1. The transmitter and receiver must 

be close to each other (less than 1 
meter);

2. The transmitter cannot perform 

link operation in the simulator and 
student mode ([System Setting] → 
[Trainer] to set);

3. There is no other WFLY 2.4GHz 

system in progress.

4. In the process of linking, if you 

need to exit the link, click the “Cancel” 
button or press the Back button.

5. After finished the link, the 

connection verification must be 
performed.

6. Telemetry: Disabling this function 

when link will affect the use of [Range 
check] [Low battery] [BUS Servo 
Setting] [Telemetry],ect.

Link steps

 (default working mode A)

1,Transmitter,enter into the menu [Linkage 

Setting] → [Link], standby.

2,Charge the receiver,pressed SET button for 3 

seconds, the LED orange light flashes.

3,Transmitter, the telemetry function is default, 

click the Link of "Start" button, the RF light flashes.

4.Verify the Link method:
1 Successfully linked, and the receiver LED light 

turns to solid green.

2 Connect to the servo, operate the transmitter, 

when thecorresponding servo has synchronous 
output action it means link successfully.

Link

Telemetry

Mode

Link

ACT

Mode A

Start

TX

 

ID:00000AA5

RX

 

ID:0000084E

ID diaplay would be enabled 

only after successfully linking

041

WARNING

NOTICE

Содержание ET Series




































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды