Wfly ET Series Скачать руководство пользователя | Manualshive

Страница: 76 / 131

background image

Idle Down

Interface path: WFLY → [Model Menu] → [Idle Down]

The idle down is usually used when landing. By operating a switch, the engine speed can be reduced.

This feature is only available when the throttle position is low.

The initial setting of the switch is [--], so ﬁrstly set the control switch (and the position of the switch).

Setup steps

1 Click the status button to enable the [Idle Down] function.
2 Click the switch button to assign the function switch and set the function open position of the switch.
3 Turn on the selected[Idle Down] control switch.
4 The engine stick is in the idle state and the rate is adjusted until the engine reaches the minimum

speed.

Please pay attention to the throttle connection here, do not let the servo exceed the stroke. (When set to

a negative rate, shift to the throttle high direction.)

The position of the throttle at
“Idle Down”.

Range:
High[-100%]Low[+100%]
Default 0%.

Function control, default [--]

Idle down

Status

Switch

Oﬀset

0

%

- -

INH

076

Model Menu\Helicopter

«
...
74
75
76
77
78
...
»

Содержание ET Series




































































































































Отзывы:

Нет отзывов

Похожие инструкции для ET Series

Бренд: 1Control Страницы: 8

Бренд: ICM Controls Страницы: 2

Бренд: jablotron Страницы: 22

Бренд: jablotron Страницы: 2

Бренд: M-system Страницы: 103

Бренд: M-system Страницы: 18

Бренд: M-system Страницы: 7

Бренд: Rain Bird Страницы: 138

Бренд: VAT Страницы: 26

Бренд: Wang Страницы: 68

Бренд: NAVITAS Страницы: 14

Бренд: IDTECK Страницы: 12

Бренд: Banner Страницы: 2

CGLine+ Web Controller

Бренд: Eaton Страницы: 28

Бренд: Voltech Страницы: 8

Бренд: MX Страницы: 12

Бренд: Automated Logic Страницы: 10

Бренд: Objective Imaging Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды