Wfly ET Series Скачать руководство пользователя | Manualshive

Страница: 7 / 131

background image

Safety Precautions

Flying Precautions

Symbols Deﬁnition

Pay special attention to the safety information of the following symbols.

If without a proper operation,it may cause dangerous accident or seriously injury or

may even cause death.

If without a proper operation,it may cause dangerous accident or seriously injury or

may even cause death,and it may cause slight hurt or probability cause bodily injure!

If without a proper operation,it may cause less possibility to serious hurt,but it may

cause hurt or bodily injure.

Prohibitions

Mandatory

Disclaimer & Warning

User should be responsible for any consequences

caused by using the product. WFLY shall not be
liable for any directly or indirectly damage, injury
and any legal liability, User shall comply with all
guidelines including but not limited to this
document.

Please follow the local laws and regulations for

regular ﬂight activities. Do not use this product to
carry out personal safety, property safety or other
bad ﬂight behaviors.

To ensure the safety of yourself and others,

please observe the following precautions:

Charge the batteries! Check transmitter and

receiver battery levels and always recharge the
batteries before each ﬂying session. A low battery
will soon die potentially, causing loss of control and
a crash. When you begin your ﬂying session, reset
your ET12 built-in timer, and during the session pay
attention to the duration of usage.

Be careful when ﬂying near electric wires, high-

rise buildings or communication facilities, as there
may be radio interference around.

Beginners should pay particular attention to the

following safety precautions! Please read carefully!
No ﬂy when user is in poor health condition such as
fatigue and drunkenness.
No ﬂy in bad weather day such as rain, strong wind
or at night, etc.
No ﬂy near high voltage wires, communication base
stations, government secret zone or public places
where crowds gathered.
No ﬂy in airports and other places where ﬂy is
forbidden.

Before ﬂying, inspect the aircraft carefully,

inspect whether the aircraft and transceiver system
it's normal. When ﬂying, make the transmitter
display to the initial interface, in case of mistaken
parameter change. After ﬂight, turn oﬀ the receiver
power before turn oﬀ the transmitter power, in case
of any injury caused by fail safe works.

More debugging, more testing, less loss, less

damage!

Power on and oﬀ sequency of transmitter and

receiver

Power on:

Firstly turn on the transmitter (ensuring the

minimum throttle position), Secondly Turn on the
receiver

Power oﬀ:

Firstly turn oﬀ the receiver, Secondly turn oﬀ the

transmitter

Transmitter and receiver low voltage may cause

fail-safe danger!

Note: The transmitter will display the warning

interface, please pay attention to the transmitter
prompt! Improperly operation may cause
accident injury to user.

007

WARNING

NOTICE

DANGER

WARNING

NOTICE

DANGER

Mandatory

Mandatory

«
...
5
6
7
8
9
...
»

Содержание ET Series




































































































































Отзывы:

Нет отзывов

Похожие инструкции для ET Series

Бренд: D-Link Страницы: 113

Бренд: D-Link Страницы: 146

Concord express

Бренд: GE Страницы: 3

HomeTec Pro CFF3000

Бренд: Abus Страницы: 13

Бренд: NAVITAS Страницы: 7

Бренд: Abus Страницы: 2

Бренд: Easy-Laser Страницы: 84

Бренд: Easy Heat Страницы: 4

Бренд: Warren Controls Страницы: 28

Бренд: EAS Electric Страницы: 89

Бренд: Harman Страницы: 2

Бренд: T-Link Страницы: 3

Бренд: Quectel Страницы: 95

Бренд: ICAS Страницы: 51

Бренд: Icar Страницы: 40

Бренд: Icar Страницы: 86

Бренд: Icar Страницы: 39

Бренд: IBP Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды