manualshive.com logo in svg

Wfly ET Series, Инструкция по эксплуатации

Поделиться
Скачать
Wfly ET Series Скачать руководство пользователя страница 8

Safety Precautions

Battery

Lithium polymer battery(Short for LiFe 

battery),please use the WFLY special charger 
only.It is important to understand the operating 
characteristics of Li-FE batteries.

IMPORTAN! 
Long term storage (more than 3 months),storage 

temperature≤45°C general storage voltage 3.7-
3.9v.Failure to follow the proceeding precautions 
can quickly result in severe, permanent damage to 
the batteries and possibly result in a fire! 

1.Do not attempt to disassemble LiFe packs or 

cells.

2.Do not allow LiFe cells to come in contact with 

moisture or water at any time.

3.Always provide adequate ventilation around 

LiFe batteries during charge, discharge, while in 
use, and during storage.

4.Do not leave a LiFe battery unattended at any 

time while being charged or discharged.

5.Do not attempt to charge LiFe batteries with a 

charger that is NOT designed for LiFe batteries, as 
permanent damage to the battery and charger could 
result.

6.Always charge LiFe batteries in a fireproof 

location. Do not charge or discharge LiFe batteries 
on carpet, a cluttered workbench, near paper, 
plastic, vinyl, leather or wood, or inside an R/C 
model or full-sized automobile! Monitor the charge 
area with a smoke or fire alarm. 

7.Do not charge LiFe batteries at currents greater 

than the “1C” rating of the battery (“C” equals the 
rated capacity of the battery).

8.Do not allow LiFe cells to overheat at any time! 

Cells which reach greater than 140 degrees 
Fahrenheit (60°C) should be placed in a fireproof 
location.

9.LiFe cells will not charge fully when too cold or 

show full charge.

10.It is normal for the batteries to become warm 

during charging, but if the charger or battery 
becomes excessively hot disconnect the battery 
from the charger immediately!! Always inspect a 
battery which has previously overheated for 
potential damage, and do not re-use if you suspect it 
has been damaged in any way. 

11.Do not use a LiFe battery if you suspect 

physical damage has occurred to the pack. 
Carefully inspect the battery for even the smallest of 
dents, cracks, splits, punctures or damage to the 
wiring and connectors.DO NOT allow the battery’s 
internal electrolyte to get into eyes or on skin—wash 
affected areas immediately if they come in contact 
with the electrolyte. If in doubt, place the battery in a 
fire-proof location for at least 30 minutes.

12.Do not store batteries near an open flame or 

heater.

13.Do not discharge LiFe batteries at currents 

which exceed the discharge current rating of the 
battery.

14.Always store LiFe cells/packs in a secure 

location away from children.

Transmitter (ET12): 

ET12 adopts the power supply mode of lithium 

battery, and the working voltage adapts to the range 
of 3.5V-13V. Using a power supply that exceeds the 
operating voltage stroke may burn the machine!

The USB interface of the ET12 cannot be 

charged. 

Please charge the battery with a 

professional charger!

Receiver (RF209S): 

The receiver's operating voltage adapts to the 

range 3.5V-13V, with anti-reverse protection slot 
(power input pole, positive and negative reverse 
protection). With a power supply that exceeds the 
operating voltage stroke, the receiver will burn out.

注意

008

DANGER

NOTICE

NOTICE

Содержание ET Series




































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды