Wfly ET Series Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 131

Wfly ET Series Скачать руководство пользователя страница 61

Trim Setting

Interface path: WFLY → [General Menu] → [Trim Setting]
In this function, you can set the amount of digital trim and the action mode, and you can select the trim

step movement under each condition, or trim the individual movement under each condition. (For example,
hover and stunt can be trimmed separately.)

Step: Adjustable travel 1-250, the default step value is 40 (the amount of motion change per trimming).

T1-T6

Link: For example, after T1 is linked, the channel assigned by the corresponding T1 will follow the action.
Switch: INH, 2 POS, 3 POS, the default "INH", control the corresponding trimming dynamic display of the

main interface. Inhibit, the main interface hides the corresponding trim switch. 2, 3 POS, the main interface
display corresponding trimming switch.

Condition: Group, single, default "group". Group modes: The same trimming data is reﬂected in all ﬂight

conditions. Single mode: Individua ltrimming adjustments are possible under each condition.

For example: applied to a powerless remote control glider.

VL, VR

Mode: Normal, P&T, and Knob are optional. Press the key twice to make the output value automatically

return to the middle (the servo to the middle). Normal, it will automatically return to the middle after release.
P&T will not automatically return to the middle. Knob, the leftmost minimum, and the rightmost maximum
(reverse setting is default).

1/2

Trim Setting

T1

T2

T3

T4

T5

40

40

40

40

ON

ON

ON

ON

Group

Group

Group

Group

Link

ON

Switch

INH

INH

INH

INH

INH

Condition

Group

Step

40

Trim Setting

VL

VR

CL-R

CU-D

Step

40

40

40

40

Mode

Normal

P

&

T

3/3

WFLY

0

-

1000

Home2

00:00.0

Model 1

User Name

12.0V

External

5.0V

Receiver

00:00.0

00:00.0

+

25

+

1000

-

500

-

500

T6

T5

T4

T3

T2

T1

ET12

RX

Condition1

12.9V

Double click to make output value
automatically return to the middle
(the servo is back)

The trimming status prompt from
the control home interface.

Two

endpoints

Midpoint

Trimming status display

061

General Menu

«
...
59
60
61
62
63
...
»

Содержание ET Series




































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды