Wfly ET Series Скачать руководство пользователя | Manualshive

Страница: 25 / 131

background image

maximum in both the positive and negative pitch
directions. For example, from -7 to +12°

6. Throttle Hold Setting

In the model menu, call the [Throttle Hold]

function setting interface, and use the [Fly
Condition] switch to switch to the throttle lock
condition interface.

Lock position setting: This function is used to

set the working position (extinguish or idle
position) of the servo under the throttle lock state.

7. The Swash Mixing Controls the

Interaction of the Ailerons, Elevators and
Paddles

Through the [Swash Mixing] under [Model

Menu], the mixing ratio of each operation of the
aileron, elevator, and pitch can be adjusted to
ensure that the swash is corrected under each
condition.

8. Throttle Mixing Setting

The swash aileron and elevator action will

cause the engine speed to decrease. This
phenomenon can be compensated by [Throttle
Mixing] under [Model Menu]. In addition, the
clockwise and counterclockwise torque changes
can be compensated for when the body rotates.

9. Gyro Sensitivity Adjustment and Mode

Switching

In the [Gyro] mixing function under

[ModelMenu], you can adjust the gyro sensitivity
or mode switching for each condition or switch
position.

● Normal (hover ﬂight): The gyroscope is the

most sensitive.

● Idle 1 / Idle 2 / Throttle Hold: Gyro sensitivity

is minimal.

10. Throttle Setting

At the end of the ﬂight, there is no need to

change the position of the throttle trim, just turn
oﬀ the engine by simply turning a ﬂameout switch.

Set in the [Throttle Cut] function of [Model

Menu]. Set the throttle lever to idle speed and
adjust the rotation position of the ﬂame-
extinguishing servo until the damper can be
closed and the movement is unimpeded.

*The throttle trigger position can be set

separately.

Gyro

Rate

Tuning

AVCS100

%

- -

0%

0%

2/2

Gyro

Gyro

Mode

Position

Condition1

Type

AVCS

Status

INH

Condition

Gyro1

1/2

17

%

Throttle hold

Status

Switch

- -

INH

Hold pos.

Speed

0

Throttle

cut

Status

Switch

Cut pos.

Throttle

17%

17%

- -

INH

025

Basic Operation

Basic setting sequence of the helicopter

«
...
23
24
25
26
27
...
»

Содержание ET Series




































































































































Отзывы:

Нет отзывов

Похожие инструкции для ET Series

Бренд: Barco Страницы: 6

Бренд: Gardigo Страницы: 8

Бренд: Gardigo Страницы: 19

Бренд: janitza Страницы: 58

Бренд: MacDon Страницы: 32

Бренд: K&K Страницы: 6

Gemini GEM-P9600

Бренд: NAPCO Страницы: 6

Gemini GEM-P816

Бренд: NAPCO Страницы: 56

Бренд: olympia electronics Страницы: 10

Бренд: York Страницы: 20

Бренд: OMC Страницы: 18

Бренд: Paradox Страницы: 2

Бренд: Paradox Страницы: 2

FrameSaver 9120

Бренд: Paradyne Страницы: 20

VeriSafe VS2-NET

Бренд: Panduit Страницы: 6

IntelliZone2 MasterStat

Бренд: Water Furnace Страницы: 44

Бренд: Zeta Страницы: 44

Бренд: WABCO Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды