Wfly ET Series Скачать руководство пользователя

Страница: 116 / 131

Aileron To Camber Flap

Aileron to camber

FLP

FLP2

Switch

Link

Left

Right

+0%

Status

INH

OFF

- -

Function status button (INH, ON, default [INH])

Function control switch (default [--])

Connect this mix to other mixes (default [oﬀ])

Interface path: WFLY → [Model Menu] → [Aileron to Camber Flap]

This mixing uses the aileron mode to operate the ﬂaps. When the aileron stick is operated, both the

aileron and the ﬂap operate simultaneously in the aileron mode, which can improve the characteristics of
the snap roll operation.

* Diﬀerent types of interface on the wing type

Adjust in positive and negative directions, range ±120%,
default 0%

By setting the switch, mixing can be turned on during ﬂight. If you want to keep it on, set it to [--], you can

also set it to [--], and the position is "On" to achieve the function normally open.

Step function: can connect this mix to other mixes.

* Flight conditions: Set the "Flight Condition" control switch in [Model Menu] → [Flight Condition].

Switching is performed by switches, and function settings are made separately.

Aileron

Aileron2

Flaps2

Flaps

116

Model Menu\Glider

Содержание ET Series




































































































































Результаты поиска

Содержание ET Series

Отзывы:

Похожие инструкции для ET Series

Бренды по названию

Популярные бренды

Wfly ET Series, Инструкция по эксплуатации

Результаты поиска

Содержание ET Series

Отзывы:

Похожие инструкции для ET Series

Бренды по названию

Популярные бренды