manualshive.com logo in svg

Wfly ET Series, Инструкция по эксплуатации

Поделиться
Скачать
Wfly ET Series Скачать руководство пользователя страница 53

General Menu

Monitor

Interface path: WFLY → [General Menu] → [Monitor]
This interface can be used to understand the servo output of each channel and confirm the servo action. 

It can also perform the servo test, such as “stroke” and “Midpoint Test”.

Operating Mode:
- "Off": The default item displays the real-time output position of all current channels.
- "Midpoint" mode: All channels, the rudder opportunity is fixed at the midpoint stroke position.
- "Dynamic" mode: All channels, rudder opportunities repeatedly.
Throttle: The throttle channel is closed by default, avoiding the throttle channel action output in case of 

causing danger.

Touch & hold
Left HOME/MON Key
Can bring up the monitor interface directly

Test

OFF

THR

OFF

Monitor

1

2

3

4

5

6

7

8

9

10 11 12

0

0

0

0

0

0

+

50

0

0

0

0

0

OFF

Dynamic

Midpoint

Monitor Application:

1 Servo action (channel) output real-time dynamic viewing. 
2 Test of the end and midpoint of the servo stroke.

Servo test function:

1 Midpoint mode: All channels (servo) are at the neutral point, and the midpoint of the servo of each 

channel can be fine-tuned, thereby fine-tuning the model.

2 Dynamic mode: All channels (servo) are cycled back and forth between the two ends, and the stroke 

adjustment is made, so that it is possible to adjust whether the magnitude of the motion of the servo of each 
channel is suitable for the model.

053

Never use the servo test mode 

when the motor is connected or the 
engine is in the start state. (It is very 
dangerous to cause the propeller or 
rotor to rotate.)

DANGER

In dynamic mode, each rudder moves at 
an angle set by the rudder angle, so do 
not perform this test while connected to 
the body. (It may cause damage to the 
servo or connector or even the body.)

WARNING

Содержание ET Series




































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды