manualshive.com logo in svg

Wfly ET Series, Инструкция по эксплуатации

Поделиться
Скачать
Wfly ET Series Скачать руководство пользователя страница 45

1/2

Fail Safe

OFF

OFF

F/S

OFF

OFF

Aileron

Elevator

Throttle

Gyro

Gyro

1

2

3

4

5

-

152

%

OFF

Pitch

6

Fail Safe

Interface path: WFLY→ [Linkage Setting] → [Fail Safe]
With this function, when the receiver cannot receive the signal normally, it will automatically run, and the 

servo rocker arm will move to the preset position (preset action). Used to protect aircraft and reduce 
unnecessary losses.

For each channel, three protection modes can be set.
1 Hold: Hold mode, the servos remain unchanged in the last operating position before fail safe. (keep the 

action).

2 F/S: Fail Safe mode, after the controller is under fail safe, the srevo is rotated to the preset position 

(preset action).

3 Off : Turns off the current channel output. (Only for some special models or some of the flight control 

board detection ports).

F/S value: Click the corresponding key to the value or 
press the confirm key to get the current stick or switch 
position parameters. (F/S value can only be displayed 
and set in F/S mode)

Reference:
 Model fail safe is very dangerous, so you should be careful when setting this function, you can refer to 

the following suggestions, or send an email to service@wflysz.com or add Skype/WeChat/WhatsApp 
account: +86-189 2382 0083.

Setting reference (only recommended settings, please set according to your actual flight situation):
1. The helicopter throttle is set to the lowest value, and the remaining channels are set to run smoothly.
2. The airplane/glider throttle is set to the lowest or low idle speed, and the other channels are set to run 

smoothly (or hovering), because the airplane/glider can slide down without power.

3. Please refer to the flight control manual for multicopters.

Additional protection features:

The ET12 provides active protection. As long as 

the telemetry function is turned on, as long as the 
RF209S receiver is still powered on, the 
transmitter needs to be confirmed to shut down! It 
can prevent the receiver from inadvertently 
shutting down and actively enter the F/S state, so 
that the model can make unexpected and 
dangerous actions to avoid loss and damage.

If your operation does not allow 
the model to move in an 
unexpected pose, be sure to land 
the monitor to check the 
receiver's battery  or the body.

Parameter value setting (Example:Airplane 3 

channel value setting Fail Safe):

Model setting requirements: Airplane channel 3 

defaults to throttle channel, we need to slow down 
the glide after the model loses signal.

Operation: Click the button on the right side of 

channel 3 to switch to “F/S” mode. The value button 
appears on the right side of the button, and the 
transmitter throttle channel hits the lowest.

When the throttle position is selected, click the 

value button of channel 3 (or click the confirmation 
button when the cursor is on the channel 3 value 
button) to set the current channel action.

* The action preset for the specific runaway 

protection is related to the actual model. Please 
check the model manual.

(Settings need to be connected to the receiver. 

When exiting this operation interface [Fail Safe] All 
the parameters set are automatically saved to the 
receiver)

045

Linkage Setting

For your safety, be sure to set up 

fail safe protection.Especially the Fail 
Safe of the throttle channel.In that 
way,the airplane flight speed is 
reduced and the helicopter is 
decelerated from the hovering state. 
It is very dangerous to drop the plane 
at high speed due to fail safe.

WARNING

Mandatory

Содержание ET Series




































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды