Wfly ET Series Скачать руководство пользователя страница 88

Страница: 88 / 131

Aileron to rudder

Rudder

Rudder2

Switch

Left

Right

+100%

Status

INH

- -

Aileron to Rudder

Aileron to rudder

Rudder

Switch

Left

Right

+100%

Status

INH

Interface path: WFLY → [Model Menu] → [Aileron to Rudder]

This function is required when mixing the rudder and ailerons. This feature allows the model to tilt to a

steeper angle.

● This function can be used to control "on" / "oﬀ" with the switch during ﬂight. (If you want to keep it on,

set it to [--], you can also set it to [--], and the position is "On" to achieve the function normally open.)

● The mixing rate of this function can be adjusted.
● Diﬀerent types of wings will display diﬀerent interface displays.
* Flight conditions: Set the "Flight Condition" control switch in [Model Menu] → [Condition]. Switching is

performed by switches, and function settings are made separately.

Winglet

Functional status (disabled, enabled, default [disabled])

Function control switch (default [--])

Position 2 mixing

Position 1 mixing

Mix left side ratio, range ±100%, default 0%

Mix right side ratio, range ±100%, default 0%

Rudder

Rudder2

Rudder

winglet

Aileron

Rudder2

winglet

Aileron2

088

Model Menu\Airplane

Содержание ET Series




































































































































Результаты поиска

Содержание ET Series

Отзывы:

Бренды по названию

Популярные бренды

Wfly ET Series, Инструкция по эксплуатации

Результаты поиска

Содержание ET Series

Отзывы:

Бренды по названию

Популярные бренды