Wexxar WF-10T Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 156

background image

WF-10T

Case Former

Machine Maintenance

9-80

9 TROUBLESHOOTING & REPAIRS

9.1

Safety

Safety Features

To safely work on the machine, disconnect the compressed air supply and power supply. The
guard doors around the WF-10T will ensure that you do not accidentally enter the machine’s
working cell while its components are energized. Never attempt to disable any of the safety
features or enter in through the discharge end while the machine is still powered.

An

‘EMERGENCY STOP’

button is provided to immediately halt all machine operation by cutting

off air supply and electrical power. This button should be pushed

IN

to stop the machine in case

of an emergency.

Precautions

•

The WF-10T Case Former is equipped with safety interlocks. Do not attempt to disable

the interlocks when repairing the machine.

•

Do not use the

‘EMERGENCY STOP’

button as the sole means of isolating power to the

machine. Disconnect power at the main breaker panel and lock it out before undertaking
repairs.

WARNING!

Any work that involves entering the control panel must
be carried out by a qualified electrician.

«
...
90
91
92
93
94
...
»

Содержание WF-10T





























































































































































Отзывы:

Нет отзывов

Похожие инструкции для WF-10T

Бренд: Unex Страницы: 5

Бренд: Keiser Страницы: 82

Бренд: Keiser Страницы: 4

Бренд: Gebhardt Anlagentechnik Страницы: 152

Бренд: Hach Страницы: 58

Бренд: Hach Страницы: 52

Бренд: Ibiza Страницы: 21

Бренд: IBASE Technology Страницы: 67

Бренд: IBC Страницы: 8

Бренд: Ibanez Страницы: 8

Бренд: IAI Страницы: 5

Бренд: jablotron Страницы: 2

Бренд: OAKWORKS Страницы: 2

Бренд: Oakton Страницы: 2

Бренд: Oakton Страницы: 2

Бренд: O2matic Страницы: 4

ThermoTweez Handpiece TT-65

Бренд: Pace Страницы: 14

Бренд: PAT Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды