
Final Fittings 12•3
FINAL FITTINGS
1
Fitting – Seat Belts
NOTE
The upper straps are mounted via eyelets
and the straps clip onto them.
The lower straps are bolted directly into the
chassis with 7/16” seat belt bolt.
1
Locate the seat belt eyelets from your
parts.4 are required in total.
2
Screw the eyelets into bushes welded to
the top of the chassis between the main
rollcage mounts (Fig 1.1).
1.1
3
Locate the waist straps on the harness
along with four 7/16” seatbelt bolt.
4
Bolt the waist straps to the bushes
welded to the chassis ensure the straps
are in the correct orientation (Fig 1.2).
1.2
5
Place washers on the bolts before fitting
the straps.
6
Repeat the process for both sides of the
car.
2
Fitting – Seats
NOTE
The seat brackets have adjustment for the
angle of the seat. The highest part of the
bracket is at the front of the seat.
Bolt the brackets to the seat and place on a
level floor and test the seat to see if it is at
the correct angle for you.
1
Locate the two seats [B] and four seat
brackets from your parts [C].
2
Bolt the seat brackets to the seat in the
desired location using M8 cap head
bolts and a washer on each (Fig 2.1).
2.1
NOTE
If you have fitted the roll cage you will have
to put the seat in at an angle, then feed the
lower harness straps in before the seat is
sitting fully on the floor.
3
With the seat sitting on the floor of the
car position the seat and test its position
to see if you can operate the controls
properly.
4
Insert four M8 cap head bolts from
inside the car through the seat brackets
and through the floor. Fit a washer
before fitting the bolt.
5
Secure the bolts with Nyloc nuts and
washers.
NOTE
The rear bolts are tricky to get in as there is
not much space available.
6
Repeat the process for the other seat
you may wish to position the passenger
seat further back to allow for leg room
from the fire extinguisher.
7
Connect the upper straps to the eyelets
and feed them through the harness
holes in the seat (Fig 2.2).
2.2
3
Fitting – Fire Extinguisher
NOTE
The fire extinguisher is mounted in the
passenger footwell. It has two plumbed in
nozzles and is activated from the driver’s
side of the scuttle and dash via a pull cord.
1
Position the extinguisher [A] in the
passenger footwell where it is not
interfering with any other part.
2
Mark the position of the bracket on the
floor of the car.
3
Remove the extinguisher and drill two
4.1mm holes through the bracket.
4
Secure the bracket to the floor with
rivets.
5
Refit the extinguisher and connect the
straps (Fig 3.1).
3.1
NOTE
The pipe for the nozzles now has to be run.
One nozzle has to be fitted on the scuttle
inside the engine bay pointing at the engine.
The other is mounted in the cockpit pointing
at the driver.
Содержание AeroRace 2008
