WaxJet 6100 Скачать руководство пользователя страница 78

Страница: 78 / 131

RS-485 Wiring

In a four-wire network it is necessary that one node be a master node

(PC) and all others be slave nodes (FoxJet controllers). The network

is connected so that the master node (SystemMaster PC)

communicates to all slave nodes (all FoxJet printers connected). The

slave nodes only communicate with the master node (they do not

communicate with each other). The polarity of the transmit and

receive data lines must be maintained. The table below shows the

connections for FoxJet controller networks.

PC PORT

REAR PORT

FRONT PORT

TX (-)

PIN 3-RX(-)

PIN 25-RX(-)

TX (+)

PIN2-RX(+)

PIN 24-RX(-)

RX (-)

PIN 1-TX(-)

PIN 13-TX(-)

RX (+)

PIN9-TX(+)

PIN 12-TX(+)

Connections are made by “daisy chaining” shielded cable to the Rear

Port jack on the 6100 controller. It will be necessary to construct a

connector with dual cables since the 6100 controller has only one

serial port available for RS-485 communication.

Controller Configuration

The FoxJet controller must have its CPU and Interface PCB

switches and jumpers set appropriately. The following pages show

the CPU board setting for a typical installation. Besides the

switches and jumpers, each controller must have an ID# selected

and NETWORK mode of operation enabled. The ID# is selected

from the Front Port by entering “ID” and then selecting an

identification number between 1-99 (first printer must be set to #01).

The network mode of operation is enabled by entering “NE” and

selecting Y from the hand held terminal. When the NETWORK

mode is enabled, the Front Port is capable of receiving commands,

but caution should be used. The unit can not distinguish between

commands entered through the Rear Port (PC connection) and the

hand held terminal. Conflicting commands or commands entered

while the network is communicating should be avoided. It is best

that the hand held terminal is set to the main screen when using

SystemMaster if it’s to remain connected to the controller.

•

Note: When LED 4 on the CPU board is illuminated, it

indicates that network communications is taking place.

6-22

Installation & Setup

Содержание 6100




































































































































Результаты поиска

Содержание 6100

Отзывы:

Похожие инструкции для 6100

Бренды по названию

Популярные бренды

WaxJet 6100, Справочное руководство по обслуживанию

Результаты поиска

Содержание 6100

Отзывы:

Похожие инструкции для 6100

Бренды по названию

Популярные бренды