manualshive.com logo in svg

Waupaca Paca-Ryde, Руководство по установке

Поделиться
Скачать
Waupaca Paca-Ryde Скачать руководство пользователя страница 61

1726 North Ballard Road, Suite 1 - Appleton, WI 54911 - 920.991.9082 

Technical Support 855.804.5774 - [email protected]

PTM30141-D

13 MAR 2018

W

E

CRUSH

HAZARD

CUTTING

HAZARD

CRUSH

HA

Z

ARD

CRUSH

HAZARD

CRUSH

HA

Z

ARD

CRUSH

HAZARD

ECO-SYSTEM

HAZARD

ELECTRIC

HAZARD

FALLING

HAZARD

CRUSH

HA

Z

ARD

PINCH

HAZARD

ADJUST RUN/LEVEL SPEED

1. Adjust leveling speed (#2) until it is approximately 6-8 feet per minute (fpm).

A. “Out” is faster.
B. Adjustment screw should be almost completely turned in when properly set, begin from

this position and adjust accordingly.

2. Adjust down speed (#9) until it matches the up speed.
3. Set high speed in both up and down directions by adjusting pressure balance (#8) until speed is

40 fpm.

A. “Out” is faster.

4. Recheck that up/down speed match and that leveling speed is within acceptable parameters,

read just if necessary.

A. If readjustments were required, recheck high speed and adjust if necessary.
B. Repeat these steps as necessary until all speeds are within acceptable parameters.

ADJUST PRESSURE RELIEF VALVE

1. Load elevator to maximum rated capacity and run the unit to ensure working pressure is less

than 740 psi.

A. If the pressure while under full load exceeds 740 psi contact technical support before

proceeding any further.

B. Take note of the pressure during this step, this is the working pressure of this particular

elevator.

*All elevators will have a slightly diff erent working pressure due to head losses

resulting from piping confi gurations and accuracy of jack plumbness.

2. Close shutoff  valve.
3. Run unit by placing a call.
4. Adjust pressure relief (#1) until pressure is 

less than 150% of working pressure

 found when run

under full load.

A. Waupaca Elevator recommends that the valve not be adjusted to below 125% of working

pressure to ensure proper operation of the elevator.

5. Open shutoff  valve.

TEST EMERGENCY MANUAL LOWERING

1. Depress emergency manual lowering button and ensure the elevator lowers.
2. If the elevator does not lower contact technical support before proceeding any further.

TEST MANUAL PUMP

1. Remove handle  from retaining clips and place inside manual pump.
2. Operate manual pump and ensure that the elevator raises.

A. Elevator will raise approximately 1/8” per pump.

3. If elevator does not raise contact technical support before proceeding any further.

VALVE ADJUSTMENTS

SERIES :

  114

116

Page 61

Содержание Paca-Ryde









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды