Waupaca Paca-Ryde Скачать руководство пользователя страница 46

Страница: 46 / 72

1726 North Ballard Road, Suite 1- Appleton, WI 54911 - 920.991.9082

Technical Support 800.238.8739 - [email protected]

PTM30113-D

16 MAR 2017

Series: All

Frameless Car Gate

Switch Installation

CRUSH

HAZARD

PINCH

HAZARD

Flipper

Place the gate switch actuator arm onto the lead post of gate, measuring 1 ¼” - 1 ½” from the

bottom of the actuator block to the top of the trim of the elevator car. Verify the gate arm will be

level on the gate and mark the holes that will need to be drilled.

With a 9/64th drill bit drill the 2 marked holes and fasten the gate switch actuator arm onto the

gate lead post with the provided hardware.

Verify the gate switch is the correct hand for the gate.

Remove the cover of the gate switch and place the cover and screws aside. Remove the (2)

knock-outs on the back of the gate switch. Fasten the gate switch to the gate switch bracket with

provided hardware. Make sure the gate switch is level on the gate switch bracket.

With the gate closed, fasten the assembled gate switch and gate switch bracket to the top of the

elevator car with provided hardware. Verify the gate actuator arm will activate the gate switch.

NOTE: If the actuator arm does not activate the gate switch, adjust

the gate switch height by loosening the hardware and moving the

gate switch up or down to the desired position and tightening the

hardware.

Verify the gate switch is fastened level on the gate switch bracket.

Open and close the gate to verify the gate switch actuates and

makes proper contact with the fl ipper.

Replace the gate switch cover.

1, 5

Gate

Switch

Bracket

Gate Switch

Actuator

Arm

Actuator

Block

Accordion

Gate

Lead Post

NOTE:

If Automatic Gate Operator is not provided,

continue installation with the instructions provide below.

If Automatic Gate Operator is provided,

follow the instructions provided with the Automatic Gate Opener.

CRUSH

HAZARD

CUTTING

HAZARD

ELECTRIC

HAZARD

BEFORE INSTALLATION REFERENCE ASME A17.1/CSA B44 CODE

1-1/4”

1-1/2”

Trim

Page 46

Содержание Paca-Ryde









































































Результаты поиска

Содержание Paca-Ryde

Отзывы:

Бренды по названию

Популярные бренды

Waupaca Paca-Ryde, Руководство по установке

Результаты поиска

Содержание Paca-Ryde

Отзывы:

Бренды по названию

Популярные бренды