Waupaca Paca-Ryde Скачать руководство пользователя

Страница: 40 / 72

1726 North Ballard Road, Suite 1 - Appleton, WI 54911 - 920.991.9082

Technical Support 855.804.5774 - [email protected]

PTE10200-A

13 MAR 2018

Series:

008, 021, 022, 114, 115, 116, 118, 210

LED Light Installation

LED Light

LED Extension Cord

(To LED light Controller)

LED Light Cover

Connector

Flexible

Conduit

Assemble all the LED light covers with the provided hardware.

Insert all the LED lights by pulling the springs back and feeding the plug and light through the

holes in the ceiling from the inside of the elevator car.

Place and temporarily secure the power supply on top of the elevator car in desired location.

Note:

While securing anything to the elevator car, verify nothing punctures through to

the interior of the elevator car.

Plug the LED extension cords into the LED lights after the desired route has been laid out. Cut the

connector off the unused end of the LED extension cord. Next feed it through the conduit until

it reaches the power supply. If the LED extension cord needs to be shortened remove it from the

conduit and cut to the desired length. Finally feed the wire back through the conduit.

Note:

Before cutting, verify you’re cutting the right end of the LED extension cords, have

enough extension cord to reach the LED light controller box and enough to for future

maintenance. ( Like changing out a light) You may need to supply your own fl exible

conduit if more than 18” is required.

Remove a knockout and connect the power supply to the car top with the provided conduit wire

harness. Wire per wiring schematic.

Knock out the holes required on the power supply for the LED lights and securely fasten the

loose whips of the LED light cover assemblies.

CRUSH

HAZARD

CUTTING

HAZARD

CRUSH

HAZARD

CRUSH

HAZARD

FALLING

HAZARD

ANTI-

STATIC

ALERT

Page 40

Содержание Paca-Ryde









































































Результаты поиска

Содержание Paca-Ryde

Отзывы:

Похожие инструкции для Paca-Ryde

Бренды по названию

Популярные бренды

Waupaca Paca-Ryde, Руководство по установке

Результаты поиска

Содержание Paca-Ryde

Отзывы:

Похожие инструкции для Paca-Ryde

Бренды по названию

Популярные бренды