Waupaca Paca-Ryde Скачать руководство пользователя

Страница: 11 / 72

1726 North Ballard Road, Suite 1 - Appleton, WI 54911 - 920.991.9082

Technical Support 855.804.5774 - [email protected]

PTM30130-E

13 MAR 2018

CRUSH

HAZARD

CUTTING

HAZARD

CRUSH

HAZARD

CRUSH

HAZARD

FALLING

HAZARD

CRUSH

HAZARD

PINCH

HAZARD

ASSEMBLE MAIN RAIL PER FIELD DRAWINGS

PEDESTAL

BASE

PEDESTAL

RAIL PIN

21" +/- 1/32"

MEASURE DISTANCE

& DIVIDE BY 2

MOUNTING

BOLTS

RAIL SEC

TION

LEVEL

11.

10.

12.

13.

14.

VERIFY ALL FASTENERS ARE SECURELY FASTENED

2, 3

RAIL AND PEDESTAL

INSTALLATION

SERIES :

116

Use fi eld drawings to determine where to center the rail on the

hoistway wall and mark a centerline.

Mark plumb line 16 5/8” over to the left or right of the

centerline.

Distance Between Guides (DBG) should be 21” apart inside

to inside.

Measure corner to corner on each section of rail

to determine if rail section is square. Loosen mounting bolts

and adjustment as necessary to ensure rail section is square.

Torque 1/2” rail fasteners to 85 ft. lbs.

Verify the rail ends are

not off set at the top and bottom of each rail section.

Set pedestal base into place on the pit fl oor.

Align fi rst section of rail with plumb line in the hoistway. Drill

(2) appropriately sized pilot holes centered in each slot per rail

bracket. Loosely fasten with architect specifi ed hardware.

To allow for the next rail section to be installed, loosen rail clip

bolts.

Insert rail pins into predrilled holes on the top installed rail

section. Align rail with the predrilled holes on the bottom of the

next rail section and carefully lower into place.

Drill (2) appropriately sized pilot holes centered in each slot per

rail bracket. Loosely fasten into place with architect specifi ed

hardware. Finish fastening rail clips from step 6. Verify rail is

plumb and level.

Torque rail clip hardware bolts to 85 ft-lbs.

Continue rail installation following the steps 6 & 7 until the rail

is completely installed.

Verify the rail install is complete and plumb. Adjust and shim if
needed. Securely fasten rail to rail backing.

Refer to fi eld drawings for pedestal and jack locations and

install both brackets in appropriate locations using a plumb line

and loosely fasten with architect specifi ed hardware.

Align jack and pedestal brackets with rail brackets. Shim as

required to match rail brackets and securely fasten hardware.

Set pedestal into pedestal base.

Hand tighten pedestal to pedestal bracket with the

following provided hardware:

(2) - 3/8”-16 x 4-1/2” Bolts (1) - Clamping Plate

(4) - 3/8” Flat Washers

(2) - 3/8” Lock Washers

(2) - 3/8”-16 Nuts

Plumb pedestal and securely fasten.

Note:

Do not over tighten, or the plate may bend and

interfere with the sling.

Page 11

Содержание Paca-Ryde









































































Результаты поиска

Содержание Paca-Ryde

Отзывы:

Похожие инструкции для Paca-Ryde

Бренды по названию

Популярные бренды

Waupaca Paca-Ryde, Руководство по установке

Результаты поиска

Содержание Paca-Ryde

Отзывы:

Похожие инструкции для Paca-Ryde

Бренды по названию

Популярные бренды