Waupaca Paca-Ryde Скачать руководство пользователя

Страница: 31 / 72

1726 North Ballard Road, Suite 1 - Appleton, WI 54911 - 920.991.9082

Technical Support 855.804.5774 - [email protected]

PTM30143-C

06 MAR 2018

Note:

Verify that both curved opening on the standoff ’s are

lined up with the round handrail prior to installation

The fl at wood handrail needs to be fastened to the

back of the wall before car assembly

CRUSH

HAZARD

CUTTING

HAZARD

FALLING

HAZARD

CRUSH

HAZARD

PINCH

HAZARD

SERIES:

ALL ELEVATOR

METAL ROUND or FLAT HANDRAIL with SPACER STANDOFFS

FLAT WOOD HANDRAIL

WOODEN DOWEL HANDRAIL with RING STANDOFFS

1. Locate

standoff spacer on appropriate wall

with the pre-drilled holes and fasten snuggly in

place with set screws facing downward. Then

loosen the set screws

2. Align the edges of the standoff so its level.

Verify the seams are free of gaps. Securely

fasten in place.

3. Align handrail with aluminum studs and press

into position on wall. Verify a tight fi t between

handrail and handrail spacer.

4. Securely fasten (2) 1/4” -20 x 1/4“ set screws in

place.

HANDRAIL

INSTALLATION

1. Locate wall with pre-drilled holes for handrail.

2. Align handrail with fastening holes and fasten

handrail to wall with (4) #10 x 3” wood screws.

1. Locate wall with pre-drilled holes for handrail.

2. Align handrail with fastening holes with set screws

facing downward.

3. Fasten handrail to wall with (4) 1” wood screws.

4. Lock handrail into position in stand off by fastening

(2) 8-32 x 3/16” set screws.

Page 31

Содержание Paca-Ryde









































































Результаты поиска

Содержание Paca-Ryde

Отзывы:

Похожие инструкции для Paca-Ryde

Бренды по названию

Популярные бренды

Waupaca Paca-Ryde, Руководство по установке

Результаты поиска

Содержание Paca-Ryde

Отзывы:

Похожие инструкции для Paca-Ryde

Бренды по названию

Популярные бренды