Waupaca Paca-Ryde Скачать руководство пользователя | Manualshive

Страница: 43 / 72

background image

1726 North Ballard Road - Appleton, WI 54911 - 920.991.9082

Technical Support 800.238.8739 - [email protected]

PTM30118-C

12/11/2012

W

E

CRUSH

HAZARD

CUTTING

HAZARD

FALLING

HAZARD

CRUSH

HAZARD

PINCH

HAZARD

2

Reference Field

Drawings For

Gate Stack

Location

CAUTION :

Over tightening top gate track screws may cause track to bend inward on the lead post of the
gate and cause added resistance, or fasteners may strip out in the ceiling. This may cause
problems when opening or closing the gate.

Bottom

Gate Guide

FOLD GATE
TOGETHER

PLUMB LINES ON
INSIDE OF CAR

1

Remove gate track from the ceiling panel. If necessary, place a mark on the sides of the track for a position locator

to aid in alignment upon installation.

Be careful not to mark in a noticeable location.

Keep in mind the screw holes

in the ceiling may be used as locators. Since the track will be reinstalled using the same holes and screws maintain
gate track orientation. Place screws off to the side for use later.

2

Collapse gate and place the bottom guides into the fl oor track .

3

Stand gate upright while maintaining the gate stack in the correct orientation (locate handle on the strike side), and
slide the track onto the wheels; Lineup the wheels properly in the track grooves.

Be careful not to slide the wheels

in

sideways.

If necessary, reference fi eld drawings for correct gate orientation.

4

Slide top of gate with gate track in place on the car ceiling in original factory location. Align the track in the same
place with the previously noted locators such as marks and/or hole locations for proper alignment.

5

Stack the gate to one end of the track (either side of the opening), and fasten the other end of the track to the
ceiling of the car using previously removed screws. Seat the screws fi rmly against the track resulting in full contact
between the track and the ceiling.

Be careful not to bend the track.

Fasten at all visible hole locations in track.

Slide the gate to the attached end of the track and fi nish fastening the track to the ceiling.

6

Slide the gate back and forth along the track observing smooth operation. If gate does not slide smoothly check for
screw heads not fully seated, wheel not properly aligned, or dirt/debris in the track.

1

3

4 5

2

1

3

4

5

ACCORDIAN GATE

INSTALLATION

SERIES :

008 -114- 115- 116 - 118 - 021 - 022 - 210

Page 43

«
...
41
42
43
44
45
...
»

Содержание Paca-Ryde









































































Отзывы:

Нет отзывов

Похожие инструкции для Paca-Ryde

Бренд: Ravaglioli Страницы: 84

Бренд: Equipter Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды