Waupaca Paca-Ryde Скачать руководство пользователя

Страница: 54 / 72

PTE10059-E

14 DEC 2017

1726 North Ballard Road, Suite 1 - Appleton, WI 54911 - 920.991.9082

Technical Support 855.804.5774 - [email protected]

CRUSH

HAZARD

CUTTING

HAZARD

CRUSH

HAZARD

CRUSH

HAZARD

ELECTRIC

HAZARD

FALLING

HAZARD

CRUSH

HAZARD

PINCH

HAZARD

STATIC

HAZARD

ELECTRICITY

Perform the following steps

before

switching automatic operation:

1. Remove pendant control.

2. Plug UPS backup into the controller.

A) Insert male controller plug into UPS battery backup/surge protection side.

B) Insert male battery backup plug into controller female plug.

3. Turn toggle switch to the “ON” Position.

4. Turn

UPS

“ON”.

5. If the unit that you are working on is equipped with EMI-

III

’s

be sure the jumper

is installed between DC and DL in the controller.

Note: The battery back-up is ONLY used for the emergency decent.

Do not switch to AUTOMATIC OPERATION mode until installation in complete.

AUTOMATIC OPERATION

SERIES :

114, 116

On and Off

Toggle

Pendant

Receptacle

Uninterruptible

Power

Supply

(UPS)

Jumper

Page 54

Содержание Paca-Ryde









































































Результаты поиска

Содержание Paca-Ryde

Отзывы:

Похожие инструкции для Paca-Ryde

Бренды по названию

Популярные бренды

Waupaca Paca-Ryde, Руководство по установке

Результаты поиска

Содержание Paca-Ryde

Отзывы:

Похожие инструкции для Paca-Ryde

Бренды по названию

Популярные бренды