Waupaca Paca-Ryde Скачать руководство пользователя

Страница: 58 / 72

1726 North Ballard Road, Suite 1 - Appleton, WI 54911 - 920.991.9082

Technical Support 855.804.5774 - [email protected]

PTE10194-D

13 MAR 2018

ELECTRIC

HAZARD

ANTI-

STATIC

ALERT

AUTO GATE PROGRAM

SERIES :

008, 021, 022, 114, 115, 116, 118, 210

Auto Gate Program

Press the Corresponding

Call Floor Button.

Move Elevator to Desired Floor.

NOTE: Elevator must be on EZ

magnet/input.

Flip SW1 to "CLOSED" POSITION.

(located inside controller)

Press the

Corresponding

Call Floor Button.

(with all doors &

gates closed)

AG1

AG2

AG3

Gray square

indicates AG

programmed to

open.

PRESS 7x

’s

NOTE:

Unit will not accept floor calls with SW1 in

closed position.

Reference chart for

number of times to

push the button.

Flip SW1 to

"OPEN" POSITION

TO END this floor's

programming.

NOTE:

Unit will not accept floor

calls with SW1 in

closed position.

Move Elevator

to Any Other Desired

Floor and Repeat.

PRESS 1x’s

PRESS 3x’s

PRESS 2x’s

PRESS 4x’s

PRESS 5x’s

PRESS 6x’s

PRESS 0x’s

Wrong Gates

Opens.

All Desired Gates

Open Correctly.

WINDING DRUM CONTROLLER SHOWN

SW1 Switch shown

in closed position

CLOSED

SWITCH POSITION

CLOSED

SWITCH POSITION

OPEN

SW1

SWI

HYDRAULIC CONTROLLER SHOWN

SW1 Switch shown

in closed position

OPEN

Closed

Page 58

Содержание Paca-Ryde









































































Результаты поиска

Содержание Paca-Ryde

Отзывы:

Похожие инструкции для Paca-Ryde

Бренды по названию

Популярные бренды

Waupaca Paca-Ryde, Руководство по установке

Результаты поиска

Содержание Paca-Ryde

Отзывы:

Похожие инструкции для Paca-Ryde

Бренды по названию

Популярные бренды