Waupaca Paca-Ryde Скачать руководство пользователя | Manualshive

Страница: 13 / 72

background image

1. Set jack cup onto pedestal.

2. Verify that socket head cap screw is installed in

bottom of jack. Set jack onto jack cup by inserting head

of screw into jack cup alignment hole.

3. Loosely fasten jack to jack brackets with U-bolt, rubber

strap and provided hardware. (Trim the rubber strap if

necessary)

Note:

Do not double up the rubber strap and

be sure to have the gap in the front of the jack.

4. Remove the plate from jack inlet port and mount Pipe

Rupture Valve (PRV) to jack with provided O-ring,

screws and washers.

Note:

Lubricate O-ring with hydraulic oil. The O-ring

and mating surfaces must be clean.

5. Attach hydraulic pipe from PRV to tank.

Note:

The inside of the pipe and attaching threads

must be clean. All hydraulic piping must meet

ASME 17.1/CSA B44 and local codes.

6. Rotate PRV as needed to maintain mechanical

clearances.

7. Plumb and securely fasten jack to jack brackets by

tightening U-bolt.

Note:

Compress rubber strap approx. 1/8” do not

over

tighten.

8. Screw tube fi tting into weep hole on the jack crown

overfl ow relief with elbow facing downward direction.

9. Press tube over tube fi tting fi rmly until tube is fully

secure, run down jack, and into drip jug (do not

obstruct any part of the elevator) and secure tube to

jack.

1726 North Ballard Road, Suite 1 - Appleton, WI 54911 - 920.991.9082

Technical Support 855.804.5774 - [email protected]

PTM30173-B

29 MAR 2018

W

E

JACK INSTALLATION

Series:

114, 116

Use a laser level to verify rail system, pedestal and jack are all
plumb and properly aligned. If the jack and rail system are not
properly installed this may cause premature seal failure, abra-
sive wearing, leaks and noise throughout the elevator system.

1.

2.

3.

4.

5.

6.

7.

8.

9.

1

2

3

4

5

6

7

8

9

Note:

Contaminated oil will cause valve problems and more intensive maintenance.

SERIES 114 SHOWN FOR
ILLUSTRATIVE PURPOSES

JACK CUP

Page 13

«
...
11
12
13
14
15
...
»

Содержание Paca-Ryde









































































Отзывы:

Нет отзывов

Похожие инструкции для Paca-Ryde

Бренд: OLEO Страницы: 12

Бренд: Kubota Страницы: 120

Бренд: Barreto Страницы: 20

Бренд: Case Страницы: 22

Бренд: Gradall Страницы: 164

Бренд: Gradall Страницы: 172

Бренд: Case Страницы: 31

Бренд: Case Страницы: 23

Бренд: Case Страницы: 22

Бренд: Case Страницы: 22

Бренд: Case Страницы: 51

Бренд: Case Страницы: 41

Бренд: Case Страницы: 51

Бренд: Case Страницы: 61

Бренд: Case Страницы: 61

Бренд: Case Страницы: 81

Бренд: Case Страницы: 81

Бренд: Case Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды