Waupaca Paca-Ryde Скачать руководство пользователя

Страница: 28 / 72

1726 North Ballard Road, Suite 1 - Appleton, WI 54911 - 920.991.9082

Technical Support 855.804.5774 - [email protected]

PTM30140-D

22 MAR 2018

CRUSH

HAZARD

CUTTING

HAZARD

CRUSH

HAZARD

CRUSH

HAZARD

CRUSH

HAZARD

CRUSH

HAZARD

ECO-SYSTEM

HAZARD

ELECTRIC

HAZARD

FALLING

HAZARD

CRUSH

HAZARD

KINK

HAZARD

CRUSH

HAZARD

PINCH

HAZARD

Note: Weight on the sling may be needed for downward direction to verify steps below.

Rail

Sling

Car

Stabilizer

Bracket

Jack

Ram

Header

SLING

WALL

FLOOR

CLEARANCE

SERIES 114 SHOWN FOR

ILLUSTRATIVE PURPOSES

SERIES :

116

VERIFY JACK TRAVEL

Verify the sling does not collide or come in contact with

anything along travel of the elevator.

At the top landing check to see if you have 4” of over travel. At

the bottom landing check to see if you have 2” of under travel.

If you do not have both, you need to adjust the rope length

and test again.

Verify the ram header guide blocks do not come in contact

with the sling guide block while jack is at max extension.

If needed adjust the top fi nal into its permanent

position.

Bypass fi nal to verify jack will ring out before ram header

collides with the end plates of the J-rail.

Locate the dead side of the wire rope, cut wire rope as close

as possible above highest wire rope clamp at a perpendicular

angle and secure wire ropes together

(Reference Proper Handling of Wire Rope page).

Verify the anti-rotation brackets are installed in the shackles

and secure.

TEST SAFETIES FOR PROPER OPERATION BEFORE

CONTINUING INSTALLATION.

Raise jack to full length of travel and check oil level in

the pump with attached dip stick. Ensure oil level is

maintained between the indented marks provided on stick.

We recommend the hydraulic oil level be checked and

maintained semi-annually.

To Install the elevator car fl oor, follow these steps below.

Walls on all cars except the

Designer hang past the

car fl oor. Before fastening

fl oor to sling be sure to

allow enough clearance

between car fl oor and

sling upright.

Drill a least (4) holes

and bolt fl oor to sling

using provided hardware

(Verify clearance between

car fl oor and all hoistway walls.
Refer to fi eld drawings for details).

Page 28

Содержание Paca-Ryde









































































Результаты поиска

Содержание Paca-Ryde

Отзывы:

Похожие инструкции для Paca-Ryde

Бренды по названию

Популярные бренды

Waupaca Paca-Ryde, Руководство по установке

Результаты поиска

Содержание Paca-Ryde

Отзывы:

Похожие инструкции для Paca-Ryde

Бренды по названию

Популярные бренды