Waupaca Paca-Ryde Скачать руководство пользователя страница 51

Страница: 51 / 72

1726 North Ballard Road, Suite 1 - Appleton, WI 54911 - 920.991.9082

Technical Support 855.804.5774 - [email protected]

PTE10100-G

15 MAY 2018

CRUSH

HAZARD

CUTTING

HAZARD

CRUSH

HAZARD

CRUSH

HAZARD

CRUSH

HAZARD

CRUSH

HAZARD

ELECTRIC

HAZARD

FALLING

HAZARD

CRUSH

HAZARD

PINCH

HAZARD

PUNCTURE

HAZARD

ANTI-

STATIC

ALERT

STOP PIT SWITCH

INSTALLATION

SERIES :

All Elevators

Stop Pit Switch Wires

Controller Terminals

Wire Number

Hydraullic

Winding Drum

Brown (Input 1)

PS1

PS2

White (Input 2)

Black (Output 2)

PS2

PS1

Grey (Output 1)

Blue

-24

1. Verify power at the controller and disconnect is “OFF”.

2. Using appropriate hardware to mount pit stop switch in the hoistway 18” above

the lowest fl oor landing and within reach from the lowest fl oor hoistway door.

Note:

If the lowest landing has 2 or more means of access you may need an

additional stop pit switch so a switch can be easily accessed from each access
point.

Per code A17.1 when the pit exceeds 1700mm (67 in.) in depth, an additional
stop pit switch is required and approximately 1200 mm (47 in.) above the pit
fl oor.

3. Attach the pit stop switch cord and route the cord to the nearest junction box

and wire to the controller box per schematic. the pit stop switch must be wired
to meet N.E.C. and local code.

Male Connector

Female Connector

WHERE MORE THAN ONE SWITCH IS PROVIDED THEY MUST BE WIRED IN SERIES.

NOTE: DO NOT CUT THE CONNECTOR ENDS OFF THE PIT STOP SWITCH CORD.

Page 51

Содержание Paca-Ryde









































































Результаты поиска

Содержание Paca-Ryde

Отзывы:

Бренды по названию

Популярные бренды

Waupaca Paca-Ryde, Руководство по установке

Результаты поиска

Содержание Paca-Ryde

Отзывы:

Бренды по названию

Популярные бренды