Waupaca Paca-Ryde Скачать руководство пользователя

Страница: 59 / 72

1726 North Ballard Road, Suite 1 - Appleton, WI 54911 - 920.991.9082

Technical Support 855.804.5774 - [email protected]

PTE10043-F

12 FEB 2018

CRUSH

HAZARD

CUTTING

HAZARD

CRUSH

HAZARD

CRUSH

HAZARD

CRUSH

HAZARD

CRUSH

HAZARD

ELECTRIC

HAZARD

FALLING

HAZARD

CRUSH

HAZARD

PINCH

HAZARD

ANTI-

STATIC

ALERT

VERIFY POWER IS “OFF” AT THE CONTROLLER AND DISCONNECT!

1. Place car top assembly on the top of the car and center

(Reference Modular Wiring Car Top Page)

2. Remove cover with alarm bell attached by removing (2) sheet

metal screws and placing to the side for use later
*If COP has a built-in e-light, skip to step 11

3. Remove black and white emergency light wires from the

terminal block.

Note:

The location of the wires and slide through the bushing

on the box.

4. Remove light cover by removing (2) pan head screws and

place off to the side for use later.

5. Place light against the interior car wall and ceiling to

determine location.

6. Remove light and mark wire location on wall or ceiling

depending on chosen mounting position, and drill 1/4” hole
through on mark. Verify the wire length is long enough to
reach the alarm box.

7. Feed emergency light wires through 1/4” hole to alarm box

and through the bushing into the alarm box.

8. Fasten light fi xture into place with appropriate hardware.

9. Fasten cover to light fi xture with (2) pan head screws

previously removed.

10. Fasten black wire to terminal 1 and white wire to terminal 2.

11. Install (2) provided fuses into circuit board.

Note:

The battery will drain when the power is not supplied to

the unit.

12. Fasten alarm cover onto box with (2) previously removed sheet

metal screws.

13. Finish car top wiring and elevator installation. When the

installation is complete press the test switch to test light
operation. Allow up to 10 hours for battery to charge before
testing.

EMERGENCY LIGHT AND

FUSE INSTALLATION

SERIES :

008, 114, 115, 116, 118, 021, 022, 210

10.

11.

12.

Black Wire

White Wire

3, 10

2, 12

4, 5, 8, 9

Page 59

Содержание Paca-Ryde









































































Результаты поиска

Содержание Paca-Ryde

Отзывы:

Похожие инструкции для Paca-Ryde

Бренды по названию

Популярные бренды

Waupaca Paca-Ryde, Руководство по установке

Результаты поиска

Содержание Paca-Ryde

Отзывы:

Похожие инструкции для Paca-Ryde

Бренды по названию

Популярные бренды