manualshive.com logo in svg

Waupaca Paca-Ryde, Руководство по установке

Поделиться
Скачать
Waupaca Paca-Ryde Скачать руководство пользователя страница 36

1726 North Ballard Road, Suite 1 - Appleton, WI 54911 - 920.991.9082 

Technical Support 855.804.5774 - [email protected]

PTM30134-E

23 MAR 2018

W

E

CRUSH

HAZARD

CUTTING

HAZARD

CRUSH

HAZARD

CRUSH

HAZARD

CRUSH

HAZARD

CRUSH

HAZARD

FALLING

HAZARD

CRUSH

HAZARD

PINCH

HAZARD

The steel tape is VERY SHARP, use care when handling.

SECURELY FASTEN ALL HARDWARE

NOTE

:  Steel tape can be installed on left 

or right side of rail system.

1/2"

TAPE READER

BRACKET

TAPE READER

1. 

2. 

3. 

1 

5.

6.

7.

2

3

4

5

4.

SERIES 116 SHOWN 

FOR ILLUSTRATIVE 

PURPOSES

STEEL TAPE AND

TAPE READER

INSTALLATION

SERIES :

  115, 116, 118

At the highest position, place steel tape bracket against 
top rail bracket and an 1/2” inward from rail bracket.   
Fasten with appropriate hardware.

Fasten steel tape onto the steel tape bracket with the 
following provided hardware:

(1) - 1/4” - 20 x 3/4” Elevator Bolt
(1) - 1/4” Flat Washer
(1) - 1/4” Lock Washer
(1) - 1/4”-20 Nut

Fasten tape reader to tape reader bracket with provided 
hardware. Do not over tighten, tape reader should pivot 
on bracket.

(1) - 1/4” - 20 x 3/4” Elevator Bolt
(1) - 1/4” Flat Washer
(1) - 1/4” Lock Washer
(1) - 1/4”-20 Nut

Feed steel tape completely through reader.

Fasten bottom steel tape bracket onto steel tape with the 
following provided hardware:

(1) - 1/4” - 20 x 3/4” Elevator Bolt
(1) - 1/4” Flat Washer
(1) - 1/4” Lock Washer
(1) - 1/4”-20 Nut

Use the steel tape to locate position of bottom bracket.  
Ensure bracket and steel tape are aligned with above 
bracket and fasten with provided hardware.  

Note: 

When fastening the bottom tape bracket, angle 

the screws downward to help take up any slack in the 
steel tape.  

Verify the tape reader is centered with steel tape and 
fasten to car with (4) - #12 x 3/4” Phillips head screws.  Do 
not pierce through the interior car ceiling. 

Page 36

Содержание Paca-Ryde









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды