Waters Xevo TQD Скачать руководство пользователя страница 209

Страница: 209 / 250

B-1

External Connections

This appendix describes the instrument’s external connections.

Warning:

The instrument is heavy. To avoid injury, use suitable

machinery and the supplied harness to lift it.

Caution:

• Contact Waters Technical Service before moving the

instrument.

• If you must transport the instrument, or remove it from service,

contact Waters Technical Service for recommended cleaning,

flushing, and packaging procedures.

See

page 4-7

Contents:

Topic

Page

External wiring and vacuum connections

B-2

Connecting the oil-filled roughing pump

B-3

Connecting the Edwards oil-free roughing pump

B-8

Connecting to the nitrogen gas supply

B-12

Connecting to the collision cell gas supply

B-14

Connecting the nitrogen exhaust line

B-14

Connecting the liquid waste line

B-17

Connecting the workstation

B-19

Connecting Ethernet cables

B-19

I/O signal connectors

B-20

Connecting to the power supply

B-25

Содержание Xevo TQD


























































































































































































































































Результаты поиска

Содержание Xevo TQD

Отзывы:

Похожие инструкции для Xevo TQD

Бренды по названию

Популярные бренды

Waters Xevo TQD, Руководство оператора, обзор и техническое обслуживание

Результаты поиска

Содержание Xevo TQD

Отзывы:

Похожие инструкции для Xevo TQD

Бренды по названию

Популярные бренды