Waters Xevo TQD Скачать руководство пользователя страница 67

Страница: 67 / 250

Combined APPI/APCI source

3-15

Removing the IonSABRE II probe and APPI/APCI source

enclosure

Required material

Chemical-resistant, powder-free gloves

To remove the combined APPI/APCI source

1. Prepare the instrument for working on the source (see

page 4-7

)

2. Remove the IonSABRE II probe (see

page 3-8

3. Disconnect the HT cable from the instrument’s front panel.

4. Disconnect the APPI drive cable from the instrument’s front panel.

5. Remove the source enclosure (see

page 4-8

6. Remove the corona pin (see

page 4-15

7. Fit the blanking plug to the pin’s mounting contact.

Warning:

The source components can be contaminated with

biohazardous and/or toxic materials. Always wear

chemical-resistant, powder-free gloves while performing this

procedure.

Warning:

To avoid electric shock, ensure that the instrument is

prepared for working on the source before commencing this procedure.

Warning:

The probe and source can be hot. To avoid burn injuries,

take great care while working with these components.

Содержание Xevo TQD


























































































































































































































































Результаты поиска

Содержание Xevo TQD

Отзывы:

Похожие инструкции для Xevo TQD

Бренды по названию

Популярные бренды

Waters Xevo TQD, Руководство оператора, обзор и техническое обслуживание

Результаты поиска

Содержание Xevo TQD

Отзывы:

Похожие инструкции для Xevo TQD

Бренды по названию

Популярные бренды