Waters Xevo TQD Скачать руководство пользователя страница 186

Страница: 186 / 250

4-110 Maintenance Procedures

5. Clear an area, lay out the soft cloth or mat, and lay the source enclosure

on its face.

6. Use the Phillips (cross-head) screwdriver to remove the 2 source

enclosure, release-handle screws, and remove the handle.

7. Use the combined 2.5-mm Allen wrench and cone extraction tool to

remove the remaining 2 lamp-drive cover screws, which were hidden by

the release handle.

8. Slide the cover off the lamp drive.

9. Use the 3-mm Allen wrench to remove the 4 source enclosure cover

screws.

10. Ease the source enclosure cover over the lamp drive assembly.

Caution:

Take care to lay the source enclosure on a smooth sur-

face. Laying it face-first on a hard object or other protrusion can

smash the glass window.

TP03204

Source enclosure
cover screws

Lamp-drive cover
screws

Release handle

Содержание Xevo TQD


























































































































































































































































Результаты поиска

Содержание Xevo TQD

Отзывы:

Похожие инструкции для Xevo TQD

Бренды по названию

Популярные бренды

Waters Xevo TQD, Руководство оператора, обзор и техническое обслуживание

Результаты поиска

Содержание Xevo TQD

Отзывы:

Похожие инструкции для Xevo TQD

Бренды по названию

Популярные бренды