manualshive.com logo in svg

Vogt TUBE-ICE 03TA, Руководство по обслуживанию, Страница: 96 / 122

Поделиться
Скачать
Vogt TUBE-ICE 03TA Скачать руководство пользователя страница 96

03TA  Service Manual 

 
SERVICE OPERATIONS 
 

4/2/14 

9-14

Removal Of Refrigerant From The Machine.

  To transfer the refrigerant charge from the machine 

into a separate container, proceed as instructed above under “Pumpdown”.  This will isolate most of 
the refrigerant in the receiver and the recovery unit can be connected to the access port (44) of the 
hand stop valve (58) at the bottom of the receiver.  Open the valve access port by turning the valve 
stem in (front seat) and operate the recovery unit until the system is considered empty. 

 

!     WARNING     ! 

Approved recovery equipment, hoses, gages, and refrigerant containers must be 

used to comply with all local and federal EPA regulations. 

!     WARNING     ! 

 
 

!     WARNING     ! 

Follow these instructions carefully. 

Severe personal injury can result from improper 

discharge of refrigerant. 

!     WARNING     ! 

 
 

!     WARNING     ! 

It is not recommended that refrigerant be transferred from a refrigeration system  

into a cylinder.  If such a transfer is made, the refrigerant cylinder must be an  

approved CLEAN cylinder -- free of any contaminants or foreign materials--and  

must be weighed continuously to assure contents do not exceed net weight specified  

by cylinder manufacturer or any applicable code requirements. 

!     WARNING     ! 

 

Refrigerant  Leaks.

    In  addition  to  testing  the  machine  for  leaks  as  instructed  under  “Refrigerant 

Charge”, it is advisable to again make a leak test after the unit has been in operation approximately 
one week.  Any noticeable change in operating conditions, other than shown on the “Certificate of 
Test” may indicate a loss of refrigerant due to a leak.  Always remove the refrigerant pressure from 
the vessel or tubing before repairs are attempted. 

 

Non-condensable Gases.

  Satisfactory operation of the machine is not possible if non-condensable 

gases (usually air) are present in the system.  Excessive condensing pressure is an indication of such 
gases.    Excessive  condensing  pressure  in  water  cooled  condensers  may  also  be  due  to  the 
accumulation  of  scale  in  the  cooling  coil  or  due  to  insufficient  cooling  water  or  excessive  water 
temperature.  See “Water Cooled Condensers”, Section 7. 

 

Содержание TUBE-ICE 03TA



























































































































Отзывы:

Нет отзывов