Vogt TUBE-ICE 03TA Скачать руководство пользователя страница 117

Страница: 117 / 122

03TA Service Manual

TABLES & CHARTS

4/10/14

11-5

TEMPERATURE - PRESSURE CHART

FOR COMMON REFRIGERANTS

DegF

R-12

R-22

R-502 R-134a MP-39 R-404a HP-80

DegF

R-12

R-22

R-502 R-134a MP-39 R-404a HP-80

-50

-7.6

-3.0

0.2

-9.0

-9.1

0.0

1.2

46.7

84.0

97.4

45.5

45.3

102.9

111.4

-48

-7.2

-2.4

0.7

-8.7

0.8

2.1

48.8

87.3

101.0

47.7

60.0

109.0

120.0

-46

-6.8

-1.7

1.5

-8.3

1.6

2.9

51.0

90.8

104.8

50.1

62.0

113.0

124.0

-44

-6.3

-1.0

2.3

-8.0

-7.9

2.5

3.9

53.2

94.3

108.6

52.3

65.0

117.0

129.0

-42

-5.8

-0.2

3.2

-7.6

-7.4

3.4

4.9

55.4

97.9

112.4

55.0

68.0

121.0

133.0

-40

-5.4

0.5

4.1

-7.1

5.5

5.9

57.7

101.6

116.4

57.5

70.0

125.0

138.0

-38

-4.9

1.3

5.0

-6.7

-6.6

6.5

6.9

60.1

105.4

120.4

60.1

73.0

130.0

142.0

-36

-4.4

2.2

6.0

-6.3

-6.1

7.5

8.0

62.5

109.3

124.6

62.7

76.0

134.0

147.0

-34

-3.8

3.0

7.0

-5.8

-5.6

8.6

9.2

65.0

113.2

128.8

65.5

79.0

139.0

152.0

-32

-3.3

4.0

8.1

-5.3

-5.2

9.7

10.3

67.6

117.3

133.2

68.3

82.0

144.0

157.0

-30

-2.7

4.9

9.2

-4.8

-4.4

10.8

11.6

70.2

121.4

137.6

71.2

85.0

148.0

162.0

-28

-2.1

5.9

10.3

-4.2

-4.1

12.0

12.8

72.9

125.7

142.2

74.2

89.0

153.0

168.0

-26

-1.5

6.9

11.5

-3.8

-3.4

13.2

14.1

75.6

130.0

146.8

77.2

92.0

158.0

173.0

-24

-0.8

7.9

12.7

-3.0

-2.9

14.5

15.5

78.4

134.5

151.5

80.3

95.0

164.0

179.0

-22

-0.1

9.0

14.0

-2.4

-2.2

15.8

16.9

81.3

139.0

156.3

83.5

99.0

169.0

184.0

-20

0.6

10.1

15.3

-1.8

-1.7

17.1

18.4

84.2

143.6

161.2

86.8

102.0

174.0

190.0

-18

1.3

11.3

16.7

-1.1

-1.0

18.5

19.9

87.2

148.4

166.2

90.2

106.0

180.0

196.0

-16

2.1

12.5

18.1

-0.4

-0.2

20.0

21.5

90.2

153.2

171.4

93.6

109.0

185.0

202.0

-14

2.8

13.8

19.5

0.3

0.4

21.5

23.1

93.3

158.2

176.6

97.1

113.0

191.0

208.0

-12

3.7

15.1

21.0

1.1

1.4

23.0

24.8

96.5

163.2

181.9

100.7

117.0

197.0

214.0

-10

4.5

16.5

22.6

1.9

2.2

24.6

26.5

99.8

168.4

187.4

104.4

121.0

203.0

220.0

-8

5.4

17.9

24.2

2.8

3.1

26.3

28.3

103.1

173.7

192.9

108.2

125.0

209.9

227.0

-6

6.3

19.3

25.8

3.6

3.9

28.0

30.2

106.5

179.1

198.6

112.1

129.0

215.0

234.0

-4

7.2

20.8

27.5

4.5

4.8

29.8

32.1

110.0

184.6

204.3

116.1

133.0

222.0

240.0

-2

8.2

22.4

29.3

5.5

5.7

31.6

34.1

113.5

190.2

210.2

120.1

138.0

229.0

247.0

9.2

24.0

31.1

6.5

6.7

33.5

36.1

100

117.2

195.9

216.2

124.3

142.0

235.0

254.0

10.2

25.6

32.9

7.5

7.7

35.6

38.1

102

120.9

201.8

222.3

128.5

146.0

242.0

261.0

11.2

27.3

34.9

8.5

8.8

37.4

40.4

104

124.7

207.7

228.5

132.9

151.0

249.0

269.0

12.3

29.1

36.9

9.6

9.9

39.4

42.6

106

128.5

213.8

234.9

137.3

156.0

256.0

276.0

13.5

30.9

38.9

10.8

11.0

41.6

44.9

108

132.4

220.0

241.3

142.8

160.0

264.0

284.0

14.6

32.8

41.0

12.0

12.2

43.9

47.3

110

136.4

226.4

247.9

146.5

165.0

271.0

292.0

15.8

34.7

43.2

13.1

13.4

46.0

49.7

112

140.5

232.8

254.6

151.3

170.0

279.0

299.0

17.1

36.7

45.4

14.4

14.6

48.3

52.2

114

144.7

239.4

261.5

156.1

175.0

286.0

307.0

18.4

38.7

47.7

15.7

15.9

50.7

54.8

116

148.9

246.1

268.4

161.1

180.0

294.0

316.0

19.7

40.9

50.0

17.0

17.2

53.1

57.5

118

153.2

252.9

275.5

166.1

185.0

302.0

324.0

21.0

43.0

52.5

18.4

18.6

55.6

60.2

120

157.7

259.9

282.7

171.3

191.0

311.0

332.0

22.4

45.3

54.9

19.9

20.0

58.2

63.0

122

162.2

267.0

290.1

176.6

196.0

319.0

341.0

23.9

47.6

57.5

21.4

21.5

59.9

65.9

124

166.7

274.3

297.6

182.0

202.0

328.0

350.0

25.4

49.9

60.1

22.9

23.0

63.6

68.9

126

171.4

281.6

305.2

187.5

207.0

336.0

359.0

26.9

52.4

62.8

24.5

24.6

66.5

72.0

128

176.2

289.1

312.9

193.1

213.0

345.0

368.0

28.5

54.9

65.6

26.1

26.2

69.4

75.1

130

181.0

296.8

320.8

198.9

219.0

354.0

377.0

30.1

57.5

68.4

27.8

27.9

72.3

78.3

132

185.9

304.6

328.9

204.7

225.0

364.0

387.0

31.7

60.1

71.3

29.5

29.6

75.4

81.6

134

191.0

312.5

337.1

210.7

231.0

373.0

396.0

33.4

62.8

74.3

31.3

78.5

85.0

136

196.2

320.6

345.4

216.8

237.0

383.0

406.0

35.2

65.6

77.4

33.2

81.8

88.5

138

201.3

328.9

353.9

223.0

243.0

392.0

416.0

36.9

68.5

80.5

35.1

35.0

85.1

92.1

140

206.6

337.3

362.6

229.4

250.0

402.0

426.0

38.8

71.5

83.8

37.0

88.5

95.7

142

212.0

345.8

371.4

235.8

256.0

412.0

436.0

40.7

74.5

87.0

39.1

39.0

91.9

99.5

144

217.5

354.5

380.4

242.4

263.0

423.0

447.0

42.7

77.6

90.4

42.0

41.0

95.5

103.4

146

223.1

363.4

389.5

249.2

269.0

434.0

458.0

44.7

80.7

93.9

43.3

43.1

99.2

107.3

148

228.8

372.3

398.9

256.0

277.0

444.0

468.0

46.7

84.0

97.4

45.5

45.3

102.9

111.4

150

234.6

381.5

408.4

263.0

283.0

449.0

479.0

TABLE 11-6

All pressures are in lbs/in

gage (psig).

Содержание TUBE-ICE 03TA



























































































































Результаты поиска

Содержание TUBE-ICE 03TA

Отзывы:

Vogt TUBE-ICE 03TA, Руководство по обслуживанию, Страница: 117 / 122

Результаты поиска

Содержание TUBE-ICE 03TA

Отзывы: