Vogt TUBE-ICE 03TA Скачать руководство пользователя страница 41

Страница: 41 / 122

03TA Service Manual

INSTALLING YOUR TUBE-ICE

MACHINE

3-19

Programming the Electronic Bin Thermostat

The electronic bin thermostat has an LCD readout that displays the temperature in the bin at the sensor.

The control has been preset and locked out at the factory to shut the machine down at 38

°°°°

F and

to re-start at 40

°°°°

The control retains the program even if power is cut to the machine. Under special

conditions, the settings may need to be changed. The lockout switch is located on the inside of the
control. Removal of the four screws on the face of the control will reveal the lock-switch.

Follow the instructions below to reset the switch.

Press the “SET” button to enter the sensors setup mode

Select between “C”- Celsius and “F” - Fahrenheit
Use the up

↑

or down

↓

key to select “F”

Press the “SET” button to set the Set point (S1 will be blinking)
Use the up

↑

or down

↓

key to set the temperature at 38

Press the “SET” button to set the Differential (DIF 1 will be blinking)
Use the up

↑

or down

↓

key to set the differential at 2

Select between “C1”- Cooling mode and “H1” - Heating mode
Use the up

↑

or down

↓

key to select “C1”

Machine will shut off when temperature drops to 38

F and come on when temperature reaches 40

Note:

The sensor will automatically exit the programming mode if no keys are depressed for a period

of thirty seconds. Any settings that have been input to the control will be accepted at that point.

DIGITAL TEMPERATURE
READING

SENSOR

SENSOR POWER

CONNECTION

CONTROL CIRCUIT

CONNECTION

FIGURE 3-12

Electronic Thermostat

Note:

If damaged, the sensor can be replaced without replacing entire unit.

Replacement sensor part #

12A2117G0901

. Electronic temperature control part #

12A2117G09

Sensor cable can be extended up to 400 feet. For more information, consult Tube-Ice

Technical

Service Department.

Содержание TUBE-ICE 03TA



























































































































Результаты поиска

Содержание TUBE-ICE 03TA

Отзывы:

Vogt TUBE-ICE 03TA, Руководство по обслуживанию, Страница: 41 / 122

Результаты поиска

Содержание TUBE-ICE 03TA

Отзывы: