Vogt TUBE-ICE 03TA Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 122

Vogt TUBE-ICE 03TA Скачать руководство пользователя страница 12

03TA Service Manual

INTRODUCTION

3/31/14

1-2

Important Safety Notice.

This information is intended for use by individuals possessing adequate

backgrounds  of  electrical,  refrigeration  and  mechanical  experience.    Any  attempt  to  repair  major
equipment may result in personal injury and property damage.  The manufacturer or seller cannot be
responsible  for  the  interpretation  of  this  information,  nor  can  it  assume  any  liability  in  connection
with its use.

Special Precautions To Be Observed When Charging Refrigeration Systems.

Only technically

qualified persons, experienced and knowledgeable in the handling of refrigerant and operation of
refrigeration systems, should perform the operations described in this manual. All local, federal, and
EPA regulations must be strictly adhered to when handling refrigerants.

If a refrigeration system is being charged from refrigerant cylinders, disconnect each cylinder when
empty  or  when  the  system  is  fully  charged.    A  gage  should  be  installed  in  the  charging  line  to
indicate  refrigerant  cylinder  pressure.   The cylinder may be considered empty of liquid R-22/404A
refrigerant when the gauge pressure is 25 pounds or less, and there is no frost on the cylinder.  Close
the  refrigerant  charging  valve  and  cylinder  valve  before  disconnecting  the  cylinder.    Loosen  the
union in the refrigerant charging line--carefully to avoid unnecessary and illegal release of refrigerant
into the atmosphere.

! CAUTION !

Immediately  close  system  charging  valve  at  commencement  of  defrost  or  thawing  cycle  if
refrigerant  cylinder  is  connected.    Never  leave  a  refrigerant  cylinder  connected  to  system
except during charging operation.  Failure to observe either of these precautions can result in
transferring  refrigerant  from  the  system  to  the  refrigerant  cylinder,  over-filling  it,  and
possibly  causing  the  cylinder  to  rupture  because  of  pressure  from  expansion  of  the  liquid
refrigerant.

! CAUTION !

Always store cylinders containing refrigerant in a cool place. They should never be exposed to
temperatures higher than 125

°

F and should be stored in a manner to prevent abnormal mechanical

shocks.

Also, transferring refrigerant from a refrigeration system into a cylinder can be very dangerous and is
not recommended.

! CAUTION !

It is not recommended that refrigerant be transferred from a refrigeration system directly into
a cylinder. If such a transfer is made, the refrigerant cylinder must be an approved, CLEAN
cylinder--free of any contaminants or foreign materials--and must be connected to an
approved recovery mechanism with a safety shutoff sensor to assure contents do not exceed net
weight specified by cylinder manufacturer or any applicable code requirements.

! CAUTION !

«
...
10
11
12
13
14
...
»

Содержание TUBE-ICE 03TA



























































































































Отзывы:

Нет отзывов