manualshive.com logo in svg

Vogt TUBE-ICE 03TA, Руководство по обслуживанию, Страница: 77 / 122

Поделиться
Скачать
Vogt TUBE-ICE 03TA Скачать руководство пользователя страница 77

03TA Service Manual 

 

TROUBLESHOOTING 

 

2/14/07 

8-5

SYMPTOM:  Freeze-up due to ice failing to discharge. 
 

POSSIBLE CAUSE 

POSSIBLE REMEDY 

Insufficient heat for thawing because of low 
condensing pressure, non-condensables 
(usually air) in system, low refrigerant charge, 
or thaw gas solenoid valve stuck closed. 

The head pressure should be maintained at 
approximately 210 PSIG for R-22 or 250 
PSIG for R-404a, which relates to 105 

o

F 

(37.8 C). This is done by a water-regulating 
valve (water-cooled units) FIGURE 9-5A, 
Section 9, or a Fan cycling switch  (air-cooled 
units) FIGURE 9-5B, Section 9.  If non-
condensables are present with the refrigerant, 
the saturated temperature will not relate to the 
pressure reading at the receiver.  The 
refrigerant level in the receiver should be near 
the operating mark at the end of a freezing 
cycle to provide enough volume for 
harvesting.  (1" = approx. 5.5 lbs. of R-22 or 
R-404a). 

Thawing time too short. 

Check the thaw timer (T), which should be 
adjusted to allow all the ice to clear the cutter 
and ice discharge opening with at least 30 
seconds to spare. 

Cutter or cutter disc does not turn. 

Check cutter reducer and drive gear for proper 
operation and alignment. Check for broken 
cutter disc or drive pin and replace as 
necessary. 

Ice backs up into cutter or discharge opening, 
jamming cutter 

Ice mushy due to concentration of solids in the 
water tank. Perform "Cleaning Procedure" and 
check automatic and adjustable blowdown.  If 
the machine discharges ice into a chute, it 
should slope at an angle of 30 degrees for 
cylinder ice and 45 degrees for crushed ice.  
Check bin stat or level control to make sure it 
will stop the machine before ice backs-up into 
the cutter. 

Extended freeze period. 

Check

 

freezer pressure switch adjustment; see 

FIGURE 9-3, Section 9, (Freezer Pressure 
Switch) and TABLE 11-6, Section 11 
(Operating Vitals). 

Compressor not unloading. 

Check compressor amps during harvest.  A 
noticeable drop in amperage should occur.  
Check unloader solenoid coil.  If coil is okay, 
replace unloader head assembly. 

 
 

Содержание TUBE-ICE 03TA



























































































































Отзывы:

Нет отзывов