Vogt TUBE-ICE 03TA Скачать руководство пользователя страница 28

Страница: 28 / 122

03TA Service Manual

INSTALLING YOUR TUBE-ICE

MACHINE

4/2/14

3-6

Piping and Drain Connections

Figure 3-4A (Air Cooled) and 3-4B (Water Cooled) show locations and sizes for all connections.

! CAUTION !

External shut-off valves must be provided in the water inlet lines.

The minimum inlet water pressure for satisfactory operation of the machine is 30 psig.

The maximum allowable pressure is 100 psig.

! CAUTION !

Make-up
Water In

Water Tank

Drain*

Condenser Water

Condenser

Water Out*

1/2” MPT

3/4” FPT

1 1/4” FPT

TABLE 3-1

Water Supply and Drain Sizes

•

The condenser water outlet and water tank drain connections must be extended

separately

to an

open drain or sump, arranged for visible discharge.

Do not trap the water tank drain line

, as

this will interfere with the operation of the automatic blowdown system. A 20 mesh strainer,
supplied with the machine, should be installed in the supply line to the condenser.

! CAUTION !

These lines must NOT be connected into a pressure tight common header

due to the possibility that warm condenser water may back up into the water tank.

The condenser water outlet MUST be piped separately to the drain.

! CAUTION !

Содержание TUBE-ICE 03TA



























































































































Результаты поиска

Содержание TUBE-ICE 03TA

Отзывы:

Vogt TUBE-ICE 03TA, Руководство по обслуживанию, Страница: 28 / 122

Результаты поиска

Содержание TUBE-ICE 03TA

Отзывы: