Vogt TUBE-ICE 03TA Скачать руководство пользователя страница 24

Страница: 24 / 122

03TA Service Manual

INSTALLING YOUR TUBE-ICE

MACHINE

4/2/14

3-2

FIGURES 3-2 & 3-3 illustrate two methods of lifting & setting Tube-Ice



machine on an ice storage

bin.

! CAUTION !

The approximate weight of the machine is 2000 pounds.

Always use equipment with adequate load-carrying capacity.

! CAUTION !

TUBE-ICE MACHINE

REMOVE CASINGS FROM MODEL HE60
BEFORE PLACING MACHINE ON BIN

ICE STORAGE BIN

WOOD BLOCKS
TWO (2) EACH CORNER

CONTROL PANEL
& SWITCH BOX

FIGURE 3-2

Forklift-&-Blocks Method

You need:

forklift truck with adequate load and height capacities

(8) 2X4 wood blocks 8 in. long

(2) wooden 2X4’s measuring 3-ft. long

pry bar

Step 1.

Position Tube-Ice



machine on forks.

Step 2.

Stack wood blocks in each corner of the drip pan on top of the ice storage bin.

Step 3.

Lift and set Tube-Ice



machine on wood blocks.

Step 4.

Remove forklift.

Step 5.

Stack 3-ft. long 2X4’s beside drip pan, overlapping front and back of bin.

Step 6.

Using a pry bar with fulcrum on 2X4’s, raise side of machine enough to remove TOP wood
blocks.

! CAUTION !

Do not remove top AND bottom blocks at the same time.

! CAUTION !

Step 7.

Repeat steps 5 and 6 on other side.

Step 8.

With machine sitting on one (1) block under each corner, repeat steps 5, 6, and 7 remove
remaining blocks. Drip pan flanges may bend slightly.

Step 9.

Straighten bent drip pan flanges.

Step 10. Check alignment of ice chute to bin opening.

Содержание TUBE-ICE 03TA



























































































































Результаты поиска

Содержание TUBE-ICE 03TA

Отзывы:

Vogt TUBE-ICE 03TA, Руководство по обслуживанию, Страница: 24 / 122

Результаты поиска

Содержание TUBE-ICE 03TA

Отзывы: