manualshive.com logo in svg

Vogt TUBE-ICE 03TA, Руководство по обслуживанию, Страница: 42 / 122

Поделиться
Скачать
Vogt TUBE-ICE 03TA Скачать руководство пользователя страница 42

03TA Service Manual 

 
INSTALLING YOUR TUBE-ICE

®

 MACHINE 

4/2/14 

3-20

 

 

Storing  Ice.   

When  storing  ice  in  a  bin,  make  sure  the  bin  control  sensors  are  mounted  in  the  bin 

properly.  Dual ice machines require a storage bin with a divider and must have two bin controls.   

A machine making one type of ice will not have a bin divider and will require only one bin control.  If 
the  machine  is  making  cylinder  ice,  the  sensor  should  be  mounted  on  the  right  side  of  the  bin.    If 
making crushed ice, the sensor should be mounted on the left side of the bin.   

 

Ice Bin Capacity.  

Crushed or cylinder ice weighs approximately 35 pounds per cubic ft. (35 lb/ft

3 

).  

As  ice  drops  into  a  bin,  it  will  pile  up  and  slope  naturally  at  about  a  45°  angle.    This  natural  slope 
should  be  taken  into  account  when  locating  the  bin  thermostat  bulb  (or  other  bin  level  control)  and 
when  calculating  the  normal  bin  capacity.    If  the  ice  is  spread  out  by  hand  in  the  bin  for  maximum 
storage  capacity,  make  sure  a  hazard  is  not  created  by  allowing  ice  to  back  up  into  the  chute  and 
jamming the cutter.  Always allow enough room below the chute for at least one harvest (cylinder 
ice  = 62 lbs. / cycle , crushed ice = 48 lbs. / cycle). 

If a two-way defector is installed below the ice chute, care should be taken to make sure it is located 
directly in the center of the stream of ice as it falls to give even distribution of the ice.  

 

When ice bin thermostats are NOT used.

   With the selector switch set on either “Auto” or “Cyl” ice, 

the  machine  will  produce  cylinder  ice  only.    If  the  switch  is  changed  to  “Cru”  while  the  unit  is 
producing  cylinder  ice,  after  the  first  5  minutes  of  a  cycle,  it  will  complete  the  freeze  and  harvest  of  
cylinder ice before changing to the production of crushed ice.  The next cycle will produce crushed ice. 

With the switch set on “Cru” the machine will produce crushed ice.  If the switch is changed to “Both 
Auto” or “Cyl” within the first 5 minutes of a cycle, the unit will revert immediately to the production 
of cylinder ice. 

If an alternate bin level control is used, it must be located in a position to stop the machine prior to ice 
backing up into the ice chute and jamming cutter. 

 

Single Ice Type.

   

No  Divider  in  bin  (cylinder  or  crushed  ice).

    With  the  selector  switch  on  “Ice”,  the  machine  will 

produce either cylinder or crushed ice. The machine will contain only one freezer pressure switch (FPS) 
and one bin Control (BC), and two selector switches (SS1 (Ice/Clean)  & SS2 (On/Off), the reversing 
relay (R) is not included. The machine will also be supplied with an ice chute without an ice deflector 
door assembly. 

 

Dual Ice Type (crushed and cylinder). 
Divider in bin (cylinder and crushed ice separately stored).

  With the selector switch on “Auto”, the 

machine  will  automatically  produce  cylinder  ice  until  the  cylinder-ice  bin  is  filled.    This  action  will 
open  the  cylinder  ice  thermostat  switch  in  the  cylinder  ice  bin  and  will  automatically  change  the 
machine over to crushed ice production--provided the crushed bin is not full.  When the crushed ice bin 
is filled, its thermostat switch opens and stops the machine upon completion of the harvest cycle. 

With the selector switch set on “Cru”, the machine will produce crushed ice until the bin is filled and 
the  thermostat  switch  opens.    It  will  then  shut  down  at  the  completion  of  the  thawing  period.    If  the 
switch is changed to “Auto” or “Cyl” within five minutes of the machine starting crushed ice freeze, it 
will not switch immediately to the production of cylinder ice. 

The  machine  will  never  stop  by  action  of  the  bin  thermostat  during  any  freezing  operation.    It  will 
always complete the evacuation and discharge of all the ice and completion of a cycle regardless of the 
causes which open either thermostat switch. 

 

Содержание TUBE-ICE 03TA



























































































































Отзывы:

Нет отзывов