manualshive.com logo in svg

Vogt TUBE-ICE 03TA, Руководство по обслуживанию, Страница: 63 / 122

Поделиться
Скачать
Vogt TUBE-ICE 03TA Скачать руководство пользователя страница 63

03TA Service Manual 

 

MAINTENANCE 

 

3/31/14 

7-1

7.  Maintenance 

 

Ice Making Section.

  The ice-making section of the Tube-Ice

®

 machine should be cleaned at least 

twice a year (more often if water conditions cause mineral build-up).  Use an approved food-grade 
ice machine cleaner.  The water pump is used to circulate the cleaner through the system by setting 
the  “Clean/Off/Ice”  selector  switch  to  “Clean"  and  starting  and  stopping  the  pump  by  the 
“Start/Manual  Harvest”  and  “Stop”  switch.    For  complete  instructions,  refer  to  the  “Cleaning 
Procedure” attached to the equipment and duplicated here. 

NOTE: Before cleaning or sanitizing any Tube-Ice machine, pump the machine down and make sure 
the crankcase heater is working properly.  This will eliminate the possibility of refrigerant migrating to 
the compressor while circulating warm water through the evaporator.

                                    

 

Cleaning Procedure 

1.

 

Before  cleaning  any  Tube-Ice  machine  make  sure  the  crankcase  heater  is  working  properly.    When  the 
crankcase heater is not working there is a possibility for refrigerant evaporated by warm circulating water 
to migrate to the compressor during the cleaning operation.                                                                        

2.

 

Set “Clean/Off/Ice” selector switch (SS) to the “Off” position.  If the machine is running, it will shut 
down on completion of the next ice harvest period. 

3.

 

Remove ice from storage area or cover opening into it. 

4.

 

Shut off water supply and drain water tank (7) by opening drain valve (39).  Remove any loose sediment 
from tank. 

5.

 

Close drain valve (39) and fill water tank (approximately 6 gallons) with warm water.  Close the petcock 
on the water pump during the cleaning period. 

6.

 

Add 16 ounces (8 ounces per 3 gallons) of Nu-Calgon

 ice machine cleaner or equivalent (a food grade 

liquid phosphoric acid) to water tank during the refill period.  Note: Tank capacity = 6 gallons 

7.

 

Inspect the water distributors by looking through clear freeze cover.  If required, remove the cover.  Clean 
and remove any solid particles from the distributor orifices (two orifices in each distributor).  Clean the 
rubber cover gasket and reinstall the cover. 

8.

 

To run the pump only, set the selector switch (SS) to the “Clean” position and press “Start”. 

9.

 

Circulate cleaning solution until deposits are dissolved or solution is neutralized.  Repeat cleaning if 
necessary. 

10.

 

Press “Stop” button to stop pump, then drain and flush water tank with fresh water.  Open water supply to 
machine. 

11.

 

Drain and flush tank and then refill with fresh water. 

12.

 

Clean inside of ice storage area and remove any solution that entered during the cleaning process.  
Remove cover if one was installed over opening into storage area. 

13.

 

Start ice-making cycle by setting the “Clean/Off/Ice” selector switch (SS) to “Ice”.  Check for water leaks 
around the freezer cover and tighten nuts if needed 

14.

 

Adjust setting of pump petcock per instructions under “Adjustable Blow down” in Section 9. 

 
 
 
 
 
 

Содержание TUBE-ICE 03TA



























































































































Отзывы:

Нет отзывов