Vogt TUBE-ICE 03TA Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 122

Vogt TUBE-ICE 03TA Скачать руководство пользователя страница 29

03TA Service Manual

INSTALLING YOUR TUBE-ICE

®

MACHINE

3-7

Water-Cooled Connections

Connect water supply to the water regulator valve on condenser water inlet connection (bottom
connection on condenser). Connect the condenser water out line to the top connection on the
condenser.

FIGURE 3-5

Water Cooled Condenser Connections

Cooling Tower.

For water cooled machines only.

When selecting a cooling tower, careful attention must be given

to operating wet bulb conditions. It is advisable to check with your local cooling tower distributor
for their recommendations based on actual operating conditions in your area. An average wet-bulb
of 78

°

F is typical in the U.S. but many localities have design wet-bulbs as low as 72

°

F or as high as

82

°

F.

The cooling tower water pump must be capable of delivering the required volume of water through
the  condenser.    Due  to  cooling  tower  location  and  pressure  drop  through  water  lines  and  water
regulating valves, the pump must be sized for each installation.  Refer to TABLE 11-1 for condenser
water requirements.  The water piping for the cooling tower and the installation of the pump must be
in accordance with the manufacturer’s instructions.

Proper  water  treatment  for  the  prevention  of  mineral  and  foreign  matter  accumulation  in  the
condenser or cooling tower is recommended.  A water analysis should be obtained to determine the
proper chemicals to use.

1 1/4” FPT
Condenser
Water Inlet

1 1/4” FPT
Condenser
Water Outlet

«
...
27
28
29
30
31
...
»

Содержание TUBE-ICE 03TA



























































































































Отзывы:

Нет отзывов