Vogt TUBE-ICE 03TA Скачать руководство пользователя страница 90 | Manualshive

Страница: 90 / 122

Vogt TUBE-ICE 03TA Скачать руководство пользователя страница 90

03TA Service Manual

SERVICE OPERATIONS

4/11/14

9-8

Sentronic Oil Pressure Safety Control.

All Sentronics utilize a pressure sensor and an electronic

control  module  to  precisely  measure  oil  pump  differential  pressure.    The  main  advantage  of
Sentronic is the elimination of the traditional capillary tubes, bellows, and pressure connections that
mechanical  pressure  switches  require  to  measure  differential  oil  pressure.    These  require  careful
handling and are known to be a source of leaks in refrigeration systems.

A second advantage of Sentronic is in the use of a precise electronic clock for the two minute time
out circuit.  Traditional mechanical controls use resistance heaters to provide the time to trip in the
event of low oil pressure.  208 volt systems, low ambient temperatures or brown-out type conditions
cause the heater output to be reduced, thus increasing the time out period from two minutes to three
or four minutes when low oil pressure conditions exist.  With the electronic clock, the time  out will
always be the same.

As  a  result  of  the  elimination  of  the  capillary  tube  measuring  system  and  a  more  precise  timing
circuit, Sentronic will improve the overall reliability of the refrigeration system.  As in the past, all
new  and  replacement  Copelametic  compressors  equipped  with  oil  pumps  require  the  use  of  a
Copeland approved oil pressure safety switch.  Failure to use an approved oil pressure safety switch
will  be  considered  as  misuse  of  the  compressor,  and  can  adversely  affect  warranty  replacement  of
the compressor should a lubrication connected failure occur.

FIGURE 9-9A

Sentronic Oil Pressure Safety Control

Sentronic/CoreSense Oil Safety (Sensor Only)

Part #:

Sentronic Oil Safety Control (Entire Unit)

Part #:

Oil Sightglass (50hz machine)

Note: Sightglass on other side

of compressor for 60hz

machines

Oil Pump

Module

Sensor

Copper

Washer

Reset Button

«
...
88
89
90
91
92
...
»

Содержание TUBE-ICE 03TA



























































































































Отзывы:

Нет отзывов